All Installation Instructions for Kenmore Refrigerator 79570323310

Old ice tray cracked and wouldn't hold water

Repair was pretty easy but be ready to possibly switch out the wiring harness. The new ice maker had a smaller connector that would not fit the connector built into the door of the fridge. I had to pull the harness from my old ice maker and swap it onto the new maker. After that was done, everything mated up perfectly and worked fine.

Parts Used:

Refrigerator Ice Maker Kit Assembly

Brandon from LIBERTY HILL, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Frost in the freezer. Icemaker frozen.

I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.

Parts Used:

Clip

Teresa from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Refrigerator light had a short in it and would randomly work

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

Parts Used:

Refrigerator Door Switch

Tammy from HAGERSTOWN, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My dishwasher was leaking water

The repair went well. They actually had to replace the motor. This saved me a lot of money having it repaired in this manner. Very professional & pleasant.

Parts Used:

Refrigerator Water Filter

rosalie from wayne, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Unit kept beeping as if the freezer door was open

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

Parts Used:

Switch,Push Button

Paul from San Jose, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light was not going on sometimes, or needed wiggling to work

purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !

Parts Used:

Switch,Push Button

Nancy from Hallandale Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light out

slid screw driver under edge of switch, easy.

Parts Used:

Refrigerator Door Switch

Jack from Ellenton, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Spring was broken on original unit, had to replace whole lever.

removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!

Parts Used:

Spring,Lever

Alan from Sun City West, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

plastic tube leaking at connector

Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.

Parts Used: