66592012102 Kenmore Range - Instructions

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Looks better than the old one wes and so easy to do. Thanks.

Only difficult because one heating element connector broken off. Before receiving correct part, tried to install generic element, which had leads about 2 inches too long, so trying to force into place bent electrical connectors that go from oven to heating element. Tried to bend one back and it broke off, so did not bend 2nd one back. Received correct heating element, and slid unbroken connector on one element side, and soldered 2nd element on. Screwed heating element in and it works fine.

removed the two screws and unhooked the old heating element. I set the new element in place and attached the electrical leads and replaced the two screws and tested the oven.

Replaced trim kit found on site. Everything went well. No real problems. I will book mark your site for the any other parts I may need.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Repair relativley easy only needed phillips screwdriver to complete repair.

since I only had one of two screws, i installed with just the one. it would not work at all using a slightly longer screw, which is very odd.

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

The detection of the part and the replacement of the upper spray arm was quite easy, because of its unique shape and function, and also because it was easy to screw in place. I saved the web order page in case this part tends to deteriorate frequently, even though it is the first time it showed this problem since we purchased this appliance.

Element burned out, ordered from Sears. Took over 2 weeks to get, originally sent wrong burner then shipped second one to wrong address. When I installed element I found that switch was also burned out . I ordered it from Parts Select & it was in the stove in 24 hours from the time I ordered it on line. Be assured I know where I will order my parts from now on

So easy. Unplug the range. (really important. You're working with wiring after all) Unscrew the metal plate holding the bake element in place, gently pull out the wires and detach the element from them. (the element just pulls off, but it was attached pretty tightly so I did have to use needlenose pliers to get a better grip on it.) Then simply plug in the new bake element, push the wires back in, reattach the metal plate and bake a cake! Don't even think about calling a repairman for this one! It took under 10 minutes once I got around to ordering the element. (none of the local stores carried them)

Replaced the burner switch.