66516053402 Kenmore Dishwasher - Instructions

removed rack
removed one screw
removed old seal
installed new seal
installed screw

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Took out the screws--found out what the problem was--ordered part (your people were helpfull--good customer people--received the part within the time I was told--installed according to the instructions--turned it on. . Working fine and guess what--I don't have to do the dishes anymore.

Pulled out the screws to the panel. Did a visual inspection and noticed a burn mark on a terminal on the circuit board. Replaced the board and now had no lights. Made sure the breaker wasn't tripped and than followed power through the dishwasher and it went to the fuse on the circuit board that you have to take from the old board and put it on the new board. Well anyway, the fuse was blown and had to get one of them. Now dishwasher works.

first things first. troubleshoot.... unit wont run. no l.e.d.s at all. Opened front panel and first thing I see is a thermal cutout mounted outside of printed circuit board. After using a multimeter to check for continuity, used a set of alligator clips with a common lead, thus bypassing thermal cutout. Viola, she worked. Ordered part after finding site with google search. Part was delivered in two days.

After researching the issue, it pointed to either a clogged hose or a bad pump. I cleaning the hose, verifying that there was no clog by using baking soda, vinegar and water. It would work, once maybe twice, then the water would sit again. I checked the line again, no issues. I purchased a new pump. The installation of the pump was easy, only to discover that this did NOT solve my problem. I am now considering a new dishwasher or purchasing a new $150 motor. It sucks not being able to send the parts back.

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

REMEMBER TO SHUT OFF POWER _ Had to remove the screws using TORX driver on the inside door edge-- then came the hard part -- the foam insulation is glued to the inner door and the outer cover- I was able to finally separate the cover leaving the foam on the inner door. Then had to break off the foam insulation on the lower third of the door up from the bottom. I then had access to the screws holding the air inlet to the door. The screws are located so you can't get a straight shot at them and it is very difficult to get at them. These screws are hex head metric and very small. When they are removed the old air inlet will come right off. Take the new one and duct tape it in place inside the door and replace the screws. I recommend doing the outer ones first and since they are the easiest to get started, then you can fight the others a little easier. After the screws are replaced and tightened replace the lower half of the insulating foam by duct taping it to the foam that remained on the inner door. Then replace the outer cover and secure with the TORX screws. This was a time consuming and tough repair. I don't recommend it to a novice.

Took me longer to find my tools than to do the repair. DId have to call the PartSelect 800 # while making repair but woman there read to me a note in their system about a redesign of the replacement part that explained exactly my question. She was VERY helpful. I will not be calling the appliance repairman again!

We took off the old one by disconnecting everything and put in the new one an re-connected everything. Aligning the pump was a little difficult.

To perform this repair do the following:
1.) Turn off power to the dishwasher
2.) Turn off water, disconnect the water supply and drain using adj. wrench and/or nutdriver, remove any contents from inside
3.) Remove screws (2) from underside cabinet, remove kick plate from bottom by removing two (2) screws there, pull out washer gently providing slack to drain hose and water line
4.) Gently place washer on side, do not invert or lean on the front side, water may enter control panel and damage it
5.) Remove the water line from Inlet valve using adj. wrench
6.) Disconnect both wires from solenoid.
7.) There is one metal screw holding the valve in place, remove it with a nutdriver, slide valve assembly out.
8.) Remove the 90 degree brass angle fitting from old valve, this may require some effort. Using thread tape, install fitting on new valve assembly.
9.) Replace parts in reverse order, using thread tape on any additional water line fittings requiring it, restoring water and power last.
10.) Run a test wash and check for leaks.
Hope this helps, it did appear to fix my problem.

Just followed the YouTube video they sent with the receipt.

removed old control panel from dishwasher by unscrewing panel inside dishwasher door then replaced with new control panel.

Drained washer with hand pump. Thermo fuse had blown. Removed control panel and substituted a 15 amp automotive ATC fuse, shimming the blades with aluminum foil. Removed dishwasher from counter niche. Tipped dishwasher, removed and inspected drain pump and recirculating pump. No apparent problems noted. Temporarily rerouted supply and drain lines and restarted. Grinding noise clearly came from the drain pump. Ordered new drain pump and replaced.replaced 20 amp thermo fuse.