Models > 66513479N412 > Instructions

66513479N412 Kenmore Dishwasher - Instructions

All Instructions for the 66513479N412
106 - 120 of 200
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
top of spray arm separated from bottom causing not to hold pressure and spin
Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.
Parts Used:
ARM-SPRAY
  • Ginger from DONIPHAN, NE
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Parts Used:
Power Cord Kit
  • Fred from SICKLERVILLE, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
top dish rack wheel failed
Replaced wheels easily
Parts Used:
Dishwasher Upper Dish Rack Wheel Mount
  • John from WILMINGTON, DE
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was not drying the dishes.
I followed installation instructions from this site and all went well.
Parts Used:
Dishwasher Heating Element
  • Mike from BOULDER, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel fell off so the top dish rack was unstable
Took out racks. And releaseed bar. Released set screws and gentley pulled out unit to expose 5/16th nuts. Removed nuts and cleaned area. Used old gaskets as the new part did not come with the gaskets, Screwed in nuts. Reset bar and set rack on carriers.
Parts Used:
Dishwasher Upper Dish Rack Wheel Mount
  • joan from TRUMBULL, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper dishrack right side support broken
1. Moved dishrack and tracks outward then moved just the dish rack only in. 2. Using screw driver, pushed plastic tongue on end cap at track and lifted off the end cap. Repeated procedure on second track on opposite side of dish rack. 3. With end caps removed, pull dish rack out and place on table. 4. Examine each track and remove any pieces of broken wheel mounts. 5. Install new wheel mount on opposite side of dish rack from good wheel mounts. 6. Slide dish rack back in place with all four wheel mounts inserted in the two tracks. 7. Reinstall the end caps on the tracks and the fix is done.
Parts Used:
Dishwasher Upper Dish Rack Wheel Mount
  • Gene from STONEHAM, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper rack support: The wheel that rolls in the track had broken
The hardest part was squeezing the tab at the end of the track to pull it up and out so that the old wheel part could be slid out and the new one in. Fortunately, the track is open on the side facing the interior of the dishwasher so you can see what you're doing. Once that was done, it was simple to snap the new part into place, slide the wheel into the track, and replace the tab at the end.
Parts Used:
Dishwasher Upper Dish Rack Wheel Mount
  • Kathryn from STAFFORD, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bracket on top dishwasher rack was broken.
Took off the old bracket with a screwdriver. Replaced with new bracket.
Parts Used:
Dishwasher Upper Dish Rack Wheel Mount
  • Cheryl from TOWSON, MD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
We had a broken wheel mount
Popped off the side stay on the rack, slid the new part on the rack and snapped it into position. Replaced the side stay on teh runner. Done!
Parts Used:
Dishwasher Upper Dish Rack Wheel Mount
  • Paul from SAN FRANCISCO, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the 4 wheels supporting the upper rack broke
The repair was very, very easy. The only tool I used were my fingers. Took me about 2 minutes. Would have been less but I forgot to remove the broken wheel before installing the new one so I had to repeat the process. This hardest part was removing the end piece from the rail. If you look closely there is a little tab that needs to be pushed forward to remove the end piece. Once that is done it's very easy. I'm sure I saved $100 vs calling a repair person. I actually purchased 2 replacement parts in anticipation of another one breaking.
Parts Used:
Dishwasher Upper Dish Rack Wheel Mount
  • Daniel from SCHENECTADY, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken dish rack wheel mount
Ordered part; took part out of box when it arrived; took broken part off; put new part on. No tools needed.
Parts Used:
Dishwasher Upper Dish Rack Wheel Mount
  • Gregg from WILLIAMSTOWN, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher stopped filling
based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.
Parts Used:
Dishwasher INLET VALVE
  • Frank from SHORELINE, WA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer repairs
Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.
Parts Used:
Rack Track Stop
  • Felix from MELBOURNE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dish rack wheels plastic broken
just replaced broken piece ,,,, very easy ,,, will use you again for parts should the need arise
Parts Used:
Lower Dishrack Wheel
  • mary from LA GRANGE PK, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Parts Used:
Dishwasher INLET VALVE
  • Kevin from MILLBURY, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 66513479N412
106 - 120 of 200