66513279K118 Kenmore Dishwasher - Instructions

Reviewed the video of this problem. Followed these instructions using a flat screwdriver to release the broken stop. Then used the same tool to set the piece firmly in place.

Removed lower kick panel and there it was on the left hand side. Removed the waterline and removed the mounting screws. Disconnected the inlet waterline into the dishwasher. Removed the bad inlet valve and replaced in reverse order.

PULLED BROKEN CLIP OFF AND SQUEEZED NEW ONE IN. I HAD TO USE PLIERS TO SQUEEZE TOGTHER SINCE i AM 77 YEARS OLD AND HANDS ARE NOT THAT STRONG ANY MORE. I HAD ALSO WATCHED THE INTERNET VIDEO TO MAKE SURE I COULD HANDLE THIS CORRECTLY. 10 MINUTES MAX TO UNLOAD TOP RACK AND PUT TOGETHER.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Disconnected power,water supply and drain.Had to pull dishwasher out to access the heater element nuts. Removed broken element and replaced with new part. Repair very easy!

this job is cake. worst part is removing dishwasher from cabinet. Disconnect water , drain , and power. reove mounting screws in upper door area. Pull unit out and lay it on its face. unplug two wire leads and remove big nuts. Roll unit upright and replace heater. roll unit back over and tighten nuts and plug leads back in. It really takes two minutes to replace heater once the unit is out of cabinet.

1. Remove the top rack
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!

1) Remove (2) dishwasher cabinetry (located on top or side) cap and screws.
2) Pull dishwasher out just far enough to access wheel tub assembly.
3) Remove old, clean area and replace with new.
“Refer to several videos buy goggling part number”.

Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.

Very simple repair when you're supplied with the proper parts. Their delivery time is exceptional !

I pulled the dishwasher out from the countertop rolled it to the side removed old clamps and hose installed new hose in kind used different hose clamps than provided turned up right pushed back in ran a cycle while looking underneath with a flashlight and saw no leaks and dishwasher has been back in use for a week now.Chris

Replaced heating element and high limit thermostat. Was suppose to fix the problem but did not. Replaced the control board and works now. All of these are easy to replace.

I removed the old retainer clip, replaced it with the new one, and pushed the spray arm onto the new retainer clip. That's it!

I loooked up the main problems associated with that model which is provided on the website and ended up ordering a heating element and a thermostat. I replaced both parts it took me about 30 minutes. The dishwasher is working again and my wife is very happy. Thanks guys!!!

The fault code suggests a problem with the washer's ability to maintain water temp. This could be caused by a failure of the tempurature sensor module, safety over-temp thermostat, or the heating element. First, I disconnected AC power at the Mains panel. I then verified that the heating element was indeed at fault by removing the dishwasher and disconnecting the leads to the heating element in the rear of the unit. I set a multi-meter to resistance and measured the element and found that it was electrically open, thus proving it was the part needing replacement. I then tested the replacement element and verified it showed low resistance. (Good). I then loosened the plastic retaining nuts with an adjustable wrench, removed the old element and replaced it with the new. The nuts were then re-installed and torqued with enough force to create a leak-tight seal as verified by pouring a gallon of water in the washer. I reconnected the leads and slid the dishwasher back into place and secured it to the counter with screws. I then turned power back on at the AC Mains panel.