66513272K112 Kenmore Dishwasher - Instructions

First i turned off the water and the power, then removed the two screws to the access panel under the door. Then remove 1 screw to the electrical box and removed the wire nuts and pulled the cable out of the box. Then disconect the water supply which is up front, but very little room to work. I didn't have to diconnect the drain hose because it was long enough for me to pull out the machine. After removing to screws that hold the machine to the counter you can pull it out. Remove 2 wire from the terminals of the heat coil. Unscrew the plastic nuts from the washer and remove. Assemble in reverse order and check for leaks. I tested the old element as well as the new element for resistance before installing.

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!

removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..

Installed new gasket and striker. By not pushing the gasket in all the way , as it is intended to, it stopped the leak. The gasket is made to push in partways or all the way. Worth the money!

I followed installation instructions from this site and all went well.

I first verified that there was 120 volt line voltage getting to the unit. I removed the outer door panel by removing the 10 torx screws located around the panel on the tub side of the door. Two of the screws are longer so note there location for reassembly. The door handle can now be removed. Pull the outer door panel away from the inner panel and remove the connector to the control board. Set the outer door aside. Remove the connector to the door latch.The latch is snapped in position at the top side. Pry using a screw driver to release. Snap new latch in position. Snap on connector, Reassemble door by first reconnecting the control panel connector. install plastic door handle. Mate door to inner panel. Note interlock tabs between outer door and inner panel near the bottom area. Install the 10 screws. The two longer screws are at the top holding the latch and handle.

I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!

the gasket fit perfectly. I took the other one out by pulling on it and put the new one in by pushing it into place with me fingers. So very easy.......... and no more leaks!!! thanks!!

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

Followed the u tube video. No problems. Will use them again.

Best recommendation I can give.

Replaced control module and then replaced touch sensors.

Installed new rail and stop clip. Less than 5 minute fix.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.