59668942802 Kenmore Refrigerator - Instructions

Removed both crispers and shelf . Inserted new rail as explained in video. Replaced everything.

Followed the instructions on the website. Removed glass shelf, installed rail and replaced salad crisper bins and glass shelf. Less than 5 minutes!

Took off the shelf abovethe rail and slid into the receiver in back and front. BTW, cant say enough good about the customer service received from Part Select! They were awesome!

Remove plastic vent cover. Just snaps out. Take out two screws that hold damper cover on. Unclip and unplug damper assembly. Snap in new assembly and plug in. Replace covers. I was pretty sure this would fix my problem after observing the damper for several days. It would stay open and when I moved it by hand it would open a little more and then close. Easy fix!

Removed the two drawers and shelve. Inserted the new crisper rail. Replaced the two drawers and put the shelve back in. Took maybe 10 minutes. Did not need any tools.

I removed the glass on top of the Crisper and replaced the Rail and then replaced the glass. Done

first unplug unit, remove clear light cover it snaps out. there are 2 slots on either side of the light housing stick the screw driver in the slot and push the tab and pull down this will unlatch the control board housing, remove the board socket plugs, and the board from the frame, on the new board you will have to snap the PC board at the pre indented line. replace in reverse and follow instruction to program the code.

Refrigerator was not cold.

I had this problem before and it was the control vale in the back of the refrigerator. I ordered it and change that out in 5 minutes. That wasn’t the problem. I had the repairman come over and within 5 minutes he told me what the problem was. He showed me where the control board was. He then walked me through the removal process.

First remove the light cover on the Freezer & Refrigerator in front where the light button is located. Pull down on the front of the light cover. It pops out.

Second, in the front of the freezer & refrigerator temp control panel put your fingertips in front of the panel and pull down it’s hard to get the pins to release but the front pins will release, then pull down a little to allow the back hooks to release. (You can use a small common screwdriver if you can’t get it with your fingertips).

Next, once the panel is removed then disconnect the wiring harness. Then bring the panel to the counter, this is where you remove the circuit card and replace it. There are 4 hooks that hold the circuit board in place. Use a small common screwdriver to push the hooks away from the board. The new board comes as one piece. The board is perforated to allow you to snap the board. Directions come with the board and how to snap it. You will need to pay attention on how you removed the board. You will need to put the new board in the same way it came out.

Once the board is re-installed and lock into position reverse the process and install the control panel back into position.

Next is the programing of the board. Follow the directions that come with the control board and you will be back in business

This task took about 15 minutes to remove & replace and to program.

I was so happy to find that i could order the part online and not have to call a repairman and pay for a service call. The prat shipped in one day! It was very easy to install. Only tip i will give is, make sure you put it in the right direction. If placed in wrong the drawers won't open.

Found instructions on You Tube how to replace Jazz P/C Board Replaced board and manually defrosted evaporator coil.Everything seems to be working fine

It took more time to open the shipping box than to slide the drawer into place :-)

I did it exactly how the video that was shown when I purchased the new rail. Following those instructions worked perfectly.

Removed the storage bins. Removed the whole shelf, remove the glass part.(clean everything while you are at it, which is why it took 15-30 minutes) Lift out old rail and replace it with the new, reinstall shelf and glass. If you choose to not to clean, just take out the glass shelf, replace rail and put it back in. .

After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!