58714134100 Kenmore Dishwasher - Instructions

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

Slid the old rack out, removed the silverware basket and put in new rack, and slid the new rack in. Had to use the pliers to attach a wheel that came off during shipping.

I removed the door panel and ran the dishwasher to determine where it was leaking. Ordered the parts. When parts arrived I removed door in order to get at the bottom door gasket, replace it, and removed the tube gasket and replaced it with new parts. The whole job was very easy for a person that's never repaired a dishwasher before. I also found that the return tube gasket at the top of the dishwasher was leaking and repaired that by making a new gasket out of a flat piece of rubber and an o-ring. All leaks have been repaired. With regards to the return tube issue, it may have only been loose and if so, I could have just tightened the return tube outlet and gotten the same results. The people at this site were excellent. Thank You

Took the old out and placed the new in its place. That simple!

Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.

Followed the YouTube instructions. Loosened 4 screws took off the front door panel and removed the old door and installed the new one. The video was very helpful!

Had trouble installing the new gasket at first. Fell inside the door, and would not stay in the groove intended for it. After watching the video on your website, learned is best to angle the gasket and work in slowly to the groove from one side. Much easier then

I simply had to take the replacement rack out of the box and put it in the dishwasher. I was sent exactly the right part, as ordered, and had no difficulties at all.

Simply pulled old gasket out with hand, and slid the new one in place!

Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.

At first I wasn't sure; I thought I had to buy the inner panel of the door. Considering that I have to minimize expenses I made it a point to tackle the problem myself. I unscrewed the outter panel off the dishwasher door and located the dispenser from inside of the inner door panel.

I unplugged the old dispenser,which was damaged, unscrewed it from the panel and removed it. I cleaned any and all debris, dirt and soap scum it had accumilated over the short years we've owned it.

Finally; after I prepared the new dispenser for installation, I placed it in position screwed it in and plugged it in, which was slightly tricky because it is pretty snug against the inside door panel. Once installed, I got my older son, 15, to help me screw in the outside panel of the door, and as he held it I screwed it on the the inside panel.

I tested it with no dishes inside by pouring just a little detergent in the new dispenser, starting the dishwasher and I stuck around in case there were any leaks or any other possible disaster that could occur.

This was exactly one week ago and all is still well. By the way, the person who took my order, I believe her name was Joann, was great. She talked to me making certain I had the right part, which I was unsure of since the diagram on your site was not quite clear. On top of that; I didn't pay for overnight service, yet my part was at my door the next day. I was amazed at the quick service and delivery. Thanks Joann!!!

Felipe,
Poughkeepsie, NY

Removed front cover. No instructions so I removed all the screws. Only the bottom 2 need to be removed(1 on each side) then push cover up to unlatch. Remove 2 wires and 6 screws. Replace soap dish unit. reinstall screws and wires. Replace front cover. The hardest part is the front cover.

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

first of all, my name is virginia , I ordered the part for my husband and because of his work schedule I decided to try to fix it myself. It was very easy, about 8 screws and it was out and the new one was in and working. see, girls can do repairs ourselves.

Removed front panel of door, to get to the screws that hold the door on the hinges. Removed door, pulled gasket with pliers from bottom of door, not easy to get out because of mineral deposits. Had to push quite hard to get new gasket in. Put every thing back together and no leaks. I live in Alaska and I tried to order the part through Sears and they wanted $18.95 for shipping for a $12.87 part. The part with PartSelect was $14.92 but only $6.95 for shipping. I ordered the part on a Tuesday and recevied it on that Friday. We in Alaska get very tired of companies thinking we live on another planet. Thank you PartSelect.