41739022890 Frigidaire Washer - Instructions

PartSelect is fantastic. Door catch broke on 3 day holiday weekend and given age of washer figured nobody would have the parts. Found PartSelect on line, ordered, paid for expedited shipping, got the part by the end of the week. Took me just a few minutes to screw in the catch and I was doing laundry again the same day. Had a little bit of a problem identifying the part on the schematics but once I figured it out everything was a breeze. Recommend PartSelect highly.

It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.

Remove front panel to expose shocks. It took some time to remove the old shocks, both were broken. The pins were somewhat difficult to reach and remove, especially the one on right for it was shoved up against the electric wiring box. We ended up putting that pin in backwards for the new shock because it was impossible to reach from rear. Putting the new shocks was easy it was removing the old ones that took most of the time. The washing machine is working perfectly now.

As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

Removed front panel, used socket to compress lock tab on plastic pins holding shocks. Still taks a little effort to get them out. The one behind a plastic drain canister is a proble as there doesn't seem to be a good method for moving that canister. I think that's why the spare pin is provided.

Sadly, my case was one of the lower percentage where the problem is in the rear bearing area. The shocks were, the top support springs were good but the rear of the washer drum was shot. Opted to replace with new washer rather than go through the much longer repair with the almost $300 in parts.

Remove top of washer, remove door lock assembly,install new assembly replace top.

I removed the front access cover and the rear cover. It was also necessary to remove the water level sensor (attached to the tub drain hose) to access one of the shocks. Not having a 1/2" deep socket, I used a 2" piece of 1/2" copper pipe to depress the locking tab on the shock attachment pins--worked great. Pulled the pins out with pliers. Putting the pins back in after replacing the shocks was easiest to do using 'channel-lock' pliers to grab the bracket and the pin head and squeeze in the pin. The only problem was that my copper pipe piece fell into the drain hose when removing one of the pins! Had to take the drain hose loose to fish it out.

Pump replacement quite simple - most difficult part of job was figuring out how to disassemble outer washing machine panels. Pump required disconnecting 2 hoses and an electrical connection.

Unbelievebly fast. I ordered on Sunday. Part was shipped on Monday and I received it on Wednesday. I removed the 2 screws from the old catch and put the new one in, in about 5 minutes. I had a load of wash running 5 minutes after that.

I removed the 2 screws that held the broken latch together. The screws were a little hard to remove. Once I removed the screws, replacing the new latch was a piece of cake.

I removed thescrews , removed the roken part and then placed the new part in replaced screws , done in under 3 minutes

I simply removed the two screws holding the existing (broken) catch and replaced the old with the new in less than 5 minutes. It could not have been easier.
I would alsolike to note that I was VERY pleased with how simple it was to find the correct part and with how quickly the part arrived at my door. I will definitely refer PartSelect to anyone who may need a new appliance part.

removed front panel and used deep socket to remove pins that hold shocks. front left shock took most of the time because of hoses and a unit in the back that needed to be released to be able to remove the pin on the bottom. the right shock was a piece of cake to replace. used a hammer to pull the pins into place (i did not use it to tap on them ) . lots of bloddy fingers from sharp edges.

I replaced both shocks, as both shocks were broken! Keep in mind that Parts select packages them in pairs. I order 2 packages or 4 shocks, guess I have another pair for ~ 5 years from now. These are located under the front bottom panel, so no need to isolate water lines or even pull this sucker away from the wall. Tight clearances are the only factor from making this really easy. Use some Vaseline to assist inserting the new plastic pins.

The parts came with instructions They stated to remove the front panel. This only gets to one side for a difficult repair. I removed the back panel then it was a snap. Easiest with two people.