3627526190 Kenmore Range - Instructions

Lift up work light cover. Remove lamp. Remove two screws from control panel. Lift up control panel. Pop out spark module from slots. Remove the 6 wires from module. Attach wires to new module - module has a diagram on it that shows where wires are attached. Push new module back into slots. Replace control panel cover, lamp, and work light. Now the burners light - the spark is MUCH stronger than before repair.

It was a simple repair removed the oven door, and the oven bottom plate. removed the screw that held the burner tube to gain access to the two screws that hold the igniter in place clipped the wires. put the new one on with butt end wire connectors instead of the wire nuts supplied. screwed the igniter back onto the burner tube put the burner tube back in place and secured it with the screw, replace oven bottom and door the whole repair took 20 minutes.

Following the recommendations of others I decided to attempt repairing the oven by myself. I unplugged the stove. I removed the oven door, the drawer, the drip pan from below the oven unit and the oven pan to access the igniter bracket. All screws were 1/4" hex head except the oven pan which were slotted. I disconnected the 2 wires. I removed the old igniter and cut the 2 wires close to the old igniter to allow extra length to splice to the new igniter. The new unit included 2 wire-nuts. It was simple to wire-nut the new wires to the old ones and install the new igniter. I reassembled the pans I had removed and the door. I plugged the stove back into the wall. The new igniter worked perfectly. My wife continues to tell me how great it is to have a working oven again and how much faster it seems to heat. I am thankful the oven didn't fail while we were cooking the Thanksgiving turkey the week before. I debated calling a repair technician or shopping for a new stove. The price of the new igniter and the description of the procedure convinced me to attempt a repair. I am very pleased with the results.

removed bottom of oven.removed heat shield.i
then unscrewed the wire nuts to the igniter.i
then tookout the burnner with the igniter attached.
i unscrewed the two screws holding the igniter
in place,and put the new one on.i then screwed
the wire nuts back on,and put it back togather.
it works great,thanks for the help.it saved me alot
of money.

First I took out the old Igniter and discovered the part I ordered did not come with any connectors, just bare wires. This is ok but I found myself searching the stores for the correct attatchments. It would be great if your web site gave the options to order these at the same time. This was my first repair of this kind so I had no idea what I was doing. I thought the part would arrive with what I needed to install it. The hardest part was getting the bolts off the under side of the Igniter. The space if very tight and at an angle that a regular took doesn't really fit. What took so long was taking the bolts off by hand. Im a single woman who likes to try to fix things first on my own. My 18 yr. old daughter was in there with me the whole time learning and finally it was her smaller fingers that were able to get the bolts into the new part. We only finger tightened the part because no tools would fit at the curved angle. I love your web site and the ease of finding the part I needed. Its the stove manufacture who made this project difficult by how they place the screws. I will use them for all my part needs in the future.

I was able to access the burner and igniter by removing the broiler drawer. The flame guard was removed with a nut driver and the old igniter with a phillips screwdriver.

The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.

After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.

Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.

I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.

Removed grills, oven bottom, heat deflector, and the two igniter mounting screws. Pulled out igniter, removed two wire twist caps and old igniter. Cut off ragged ends of wires coming from the stove side and re-stripped the wire ends. Attached oven side wires to new igniter wires using new twist caps. Reassembled everything in reverse order. Tested oven operation to ensure that the gas ignited promptly. (It did).

Removed the two screws that hold the oven bottom to expose the glow element. Also removed the lower draw to get to the connections. The job was only complicated by getting to the two bolts holding the glow plug to the oven frame. Getting them off and getting the new plug on was not easy with standard tools. There was not a lot of room to work the hex bolts and i wound up cutting the old unit out and attaching the bolts to the frame and cutting slots in the new unit so I could slot it in. That worked. The glow plug was the problem and the oven came right on.

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore name on it.
I found out that even though the old ignitor glows well, it may not pull enough amps to open the gas valve.
First i disconnected the two wires on the gas safety valve that lead to the ignitor. These are accessed after taking the bottom drawer out. Then using a nut driver, i took out the two screws holding the bottom of the burner tube. Then inside the oven, i took out the racks and then the two screws in the back on the bottom. Then took out the bottom plate. I removed the one screw on the front of the burner tube, and removed the burner tube with the ignitor attached. I cut the wires off the old ignitor and attached them to the new ignitor with the supplied ceramic wire nuts. I attached the new ignitor to the burner tube and put everything back together. The bottom screws on the burner tube were very difficult for me to reach. Almost impossible to get both hands there to do the job.

Unplugged the oven. First i removed the 2 screws from the pan at the bottom of the oven and took the pan out. Next i took out the drawer underneath and took the screws out of the pans below to get to the ignitor. Unscrewed the ignitor and cut the wires below it to splice the new ignitor on. Spliced the two sets of wires and put the ceramic wire nuts on. Replaced the top and bottom pans and put the drawer back. plugged the oven back in and started the oven right up. Pretty easy.

After removing two layers of the oven floor I could not get at the igniter's wire connections. I found out that the new igniter was shipped with two wire nuts made of porcelain instead of plastic, so they were heat tolerant. Because of this, I was able to unscrew the original part and just cut the wires. I then installed the new igniter and spliced the wires of the new part to the cut wires that lead to the old part using the porcelain wire nuts and tucked the connections out of harms way. It worked fine.

My husband removed the two screws t hat hold the element in place, Then he pulled the element out about 3 inches and disconnected the two wires and replace the element with the new igniter put everything back and now its working like a charm

First shut down electric power to oven. remove
oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires.
installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.

First i removed the inside bottom of the oven where i could get to the actual glow plug igniter and removed the two screw that held the igniter in place. I than pulled the entire oven out allowing me to access the two wires connecting the igniter to the stove. I disconnected the wires and had to splice the wires as to be able to reach the appropriate connections. I reinstalled the igniter and upon testing the igniter worked properly. The entire process took me one hour.