All Installation Instructions for Kenmore Range 36272221203

my ignitor stopped working ,then the gas pressure regulator and safety valve needed replacing.

Super easy for me! My son-in-law is a contractor, I gave him the parts and let him do the work.

Parts Used:

Single Gas Pressure Regulator and Safety Valve Assembly

Myra from SCOTLAND, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

tube that sends gas to burners broke both left and right front this happen due to opening the range hood to clean inside

I turn gas off to the appliance then I remove the old gas lines and installed the new ones. I did find it easlier to attach the line at the burner knob first then attach it to the burner.

Parts Used:

Burner Tube - Left Front

Burner Tube - Right Front

LEAH from YUMA, AZ
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

BASE OF BULB BROKE OFF & WELDED TO SOCKET

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Parts Used:

RECEPTACLE PUSH-IN

NEIL from ROCKY POINT, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

finish on old oven bottom was damaged

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

ERNEST from MANCHESTER, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Getting thew the back

I put it in the same way tuck it out

Parts Used:

Oven Thermostat

William from BOSCOBEL, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the tubes both leaked

replacement was a snap and took only a small adjustable wrench and a flashlight. asome slight bending of the tube was required, but a gentle hand solved the problem easily.

Parts Used:

Burner Tube - Left Front

Burner Tube - Right Front

PHILL from SOMERSET, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Only A "Cosmetic" Replacement.

No job here. . . . Just sat new parts on to replace old ugly parts.

Parts Used:

Double Burner Pan - Left Side

Double Burner Pan - Right Side

Jimmy from Bonifay, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

while cleaning I broke the tubes either lifting or closing the top.

I bent the tubes very slghtly to rech the area of attachment. I first screwed them with my hand then tightened them with an adjstable wrench. It was really simple and fast.

Parts Used:

Burner Tube - Left Front

Burner Tube - Right Front

DAPHNE from CHICAGO, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Range burners would not light

Lift up work light cover. Remove lamp. Remove two screws from control panel. Lift up control panel. Pop out spark module from slots. Remove the 6 wires from module. Attach wires to new module - module has a diagram on it that shows where wires are attached. Push new module back into slots. Replace control panel cover, lamp, and work light. Now the burners light - the spark is MUCH stronger than before repair.

Parts Used:

Burner Spark Module - 120V 60Hz

Gregory from Washington, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Front burners had to be lit with lighter

My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.

Parts Used:

Burner Tube - Left Front

Burner Tube - Right Front

Marie from Woodstock, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

worn and pitted burner caps

Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.

Parts Used:

Burner Cap - Large

Ann from Ashland, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burners would not light

Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.

Parts Used:

Burner Tube - Left Front

Burner Tube - Right Front