Models > 3500PPW > Instructions

3500PPW Magic Chef Range - Instructions

All Instructions for the 3500PPW
106 - 120 of 343
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old element caught fire, replaced with new one
Removed screws of old element pulled clips off replaced with new element very easy
Parts Used:
Oven Bake Element
  • louis from CAHOKIA, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the lower oven element
Unplug the 220 cord..remove rear metal back ( 7-8 Ph/screws)... disconnect the red & yellow connectors from the back of the lower element. Remove-the-lift-off Oven door. Remove the two Ph/screws (one on either end of the element) At the very rear of the oven. Install the new element and reverse the about to reassemble.
Parts Used:
Oven Bake Element
  • Tom from ROCKTON, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner receptacle failed (stove over 30 years old)
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Parts Used:
Surface Burner Receptacle Kit
  • BETH from COUNCE, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The bake oven element burned out
Removed two screws and disconnected the element. Reconnected the new element and reinstalled the screws
Parts Used:
Oven Bake Element
  • Robert from LEXINGTON, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
thermostat control for large eye on range
removed several screws, removed old controller, installed new controller buttoned back up works perfect
Parts Used:
Range Infinite Burner Switch - 8 Inch
  • MILLARD from LOOKOUT MTN, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bottom bake element broken and burned
First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.
Parts Used:
Oven Bake Element
  • Carolyn S from white oak, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element had burnt in half.
Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.
Parts Used:
Oven Bake Element
  • Joyce from ROCHESTER, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.
Stuck the new one into the plugin.
Parts Used:
Economy Y-frame Surface Unit - 8"
  • RICHARD from SHOW LOW, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip Pans were stained and burned on.
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Sandra Collignon from SANTA CLAUS, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner plugs were loose
used the supplied parts...very easy. The parts were exact replacements.
Parts Used:
Surface Burner Receptacle Kit
  • James from CONCORD, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace broken bake element
Unplugged the range. Took our the oven shelves. Unscrewed the bars holding the broken bake element to the back of the oven wall. Gently pulled out the wiring to which the bake element is attached. Slipped the ends of the broken bake element off the ending on the wiring. Then slipped the ends of the new bake element over the ends on the wiring. Then pushed the wiring with attached bake element back into their position behind the oven wall and attached the bars holding the bake element to the back of the oven wall. This is really easy because it is exactly like the on-line video, for I am a 75 year old female with little technical experience.
Parts Used:
Oven Bake Element
  • Frances from MOREHEAD, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
No problem Took off old ones and replaced with new.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Nicki from ELSIE, NE
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
snapped element
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering
Parts Used:
Oven Bake Element
  • Paul from Yukon, OK
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old drip bowls were rusting, no chrome left
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch
  • kathryn from piqua, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Couldn't find correct drip bowls that fit.
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch
  • Lowell from Hardin, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 3500PPW
106 - 120 of 343
Back to Top