2VED21ZKFW02 Whirlpool Refrigerator - Instructions

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Removed right hand door of side by side. Replaced both cams and put door back. All is well.

Very simply change old part just by hand

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I removed the screws holding the handle pieces to the refrigerator, then put the new handle in place and screwed in the screws.

I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.

First I removed the three screws on the top hing of the refrigerator door so that we could lift it off the bottom hing. Socket wrench bits for my drill made that fast and simple. I lifted the door off the bottom hing to find the door closing plastic cam to be broken in several pieces. The hardest part was getting the cylinder shape piece that had broken off the cam out from inside the door. This way we would be able to insert the new piece. Needle nose pliers are the right tool for that job since the hole is small and the plastic just frays under force from regular pliers. It took some force and patience to get that out, but once all the broken pieces were removed, reassembly was quick and easy

I removed the three small bolts (under cosmetic cap) located on the right top hand side of the refrigerator and pulled off the door. Replaced the top and bottom cams, put back on the door, screws and cap. Door works like new and the Wife loves it.

On a side note, don't be confused when ordering the top and bottom cam as they are both on the bottom of the door.

Removed the top hinge cap. Removed the 3 screws with a nutdriver. Lifted the door off of the bottom hinge and placed it on it's side. Then I removed both closing cams (one screw holding each). Clean the area then replaced each cam. I put some vaseline on the bottom cam and replaced the door. 4-5 minutes not counting removing and replacing the food inside the door shelves. I'm 56 years old and have always done most of my own handywork. I don't remember any job going so smooth and fast! Ever!

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

Remove all contents from refrigerator door. Removed top hinge (3 machine screws). Remove door & place on table. Remove closing cam from bottom of door & install the replacement-reassemble. Very easy repair for a very annoying problem. Lots of descriptions on You Tube as well.

Turn fridge off. Removed top hinge cover. Removed three screws in top hinge. Lifted hinge from door. Lifted door off bottom hinge. Place door on level surface and removed old cam with socket set. Installed new cam. Removed old cam from bottom hinge with socket set. Installed new cam. Cleaned bottom of door while had easy access. Placed door back on bottom hinge. Install top hinge and screws. Finished.

Remove replace door with new cams.