25344502607 Kenmore Refrigerator - Instructions

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

took the screw out of the white flange on the top of the door that attaches to the top of the refrigerator. Then removed the cover , and the two screws attached to the refrigerator top. Then lifted off the door removed the bottom plate that is holding the plastic door holder. and replaced the broken part and replaced the bottom plate , set the door back on the hinge and installed the top two screws and the flange cover and the last screw holding the flange cover in place. It actually took longer to type this than the repair

I got the part, hitched it up and it started working right away it fit in easily, and the directions were easy to follow thank you

I ordered a replacement on-line (real simple, visual aids helped more than model nos). Once I received it in the mail, I installed it (no tools required) and now my water filter and ice maker are back to doing what they do best!

Removed the ice box and used a long screw driver to remove thhe two screws holding the motor, unplugged the motor and replaced it with the new one. A fairly easdy job that took 20 min.

Removed the door marking the top hinge placement prior to removal. Pulled the door the rest of the way off. There wasn't anything keeping it attached on the bottom right side. Turned the door upright dug out the old broken cam and replaced it with a new one. Thank you for your web-site. It saved us $$$ you have gained two new fans to your web-site. I have shared your link with many. To to anyone who is having a popping noise when you open your door. Do panic. Log on to Part Select .com. It is your only source of sanity.

Thank you

Liz

I removed the screws holding the shield covering the filter housing and cup. Unscrewed the cup, removed the filter. Then removed the pressure fittings holding the water lines on the housing. Then I removed the housing. Reversed the process with the new housing.

Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.

Before removing door, remove everything from on the door including the shelves, then close the door. Using a step ladder to access the top of the door, I removed the plastic hinge cover at the top of the refrigerator door using a Philips head screwdriver, remove the screw located at the back of the cover and slide the cover forward and up to remove. This will expose the two 3/8 machine screws that hold the top hinge bracket. Remove the screws using a socket or wrench. Then lift up on the hinge bracket from the top of the door to remove it. As long as the door is closed it will remain stable with little pressure to keep from falling. Then lift the entire door from the bottom hinge assembly and lay it across an arm chair or flat elevated surface so you can access the bottom door hinge bearing. You will see a bracket screwed to the bottom of the door with two 1/4 machine screws, it is the door stop bracket and this has the door hinge bearing inserted through it. My bearing was broke in half , the first piece fell out when I removed the door and the other piece was still inserted in the door. I removed one 1/4 screw from the stop bracket and loosened the other screw to allow the bracket to swing away from cavity that holds the bearing. Using needle nose pliers I remover the broken piece of the bearing. This part is nylon or plastic and can be cut into pieces if need be to remove it. Once removed, I cleaned the cavity, reinstalled the stop bracket assembly then inserted the new bearing. Gently align the door to the bottom bracket and set it in place, a second set of eyes may help. Once the door has been seated and in the closed position replace door bracket and the two 3/8 screws at the top of the door, check the alignment before you tighten. Check door operation! Then tighten the screws and replace the plastic cover by pressing down on the cover and sliding it back to align the Philips screw to be replaced .

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

Easy to remove the auger Motor and Solenoid, however, it didn't fix the problem. $300.00 into it I now have to purchase a circuit board for $382.00. Not a happy camper.

Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.