25344493703 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
freezer filled up with ice leaking from ice maker shut off valve bad
It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.
Parts Used:
-
Harry from Orange City, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic door holder broken
took the screw out of the white flange on the top of the door that attaches to the top of the refrigerator. Then removed the cover , and the two screws attached to the refrigerator top. Then lifted off the door removed the bottom plate that is holding the plastic door holder. and replaced the broken part and replaced the bottom plate , set the door back on the hinge and installed the top two screws and the flange cover and the last screw holding the flange cover in place. It actually took longer to type this than the repair
Parts Used:
-
Bill from Lady LAke, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One blade broke from condenser fan
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
Parts Used:
-
Chris from Lockport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
10 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker Broken
I got the part, hitched it up and it started working right away it fit in easily, and the directions were easy to follow thank you
Parts Used:
-
Philip from Hemet, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice not dispensing
removed cover, loosened the control module, removed old ice-actuator, installed new ice-actuator, re-installed cover plate. The flex cable going into the cover is somewhat of a pain to re-install.
Parts Used:
-
Buckley from Vancouver, WA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rust on Front Plate and Drive Blade
Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.
Parts Used:
-
Wayne from Westford, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
6 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker non functioning, Ice maker not sending signal for w
Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.
Parts Used:
-
Marcus from Bessemer, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Drum
Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.
Parts Used:
-
Jubal from OZARK, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
None
-
David from OSCEOLA, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker stopped making ice.
The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.
Parts Used:
-
Thomas from WESTAMPTON, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
8 loud pops and then dump ice .
Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .
Parts Used:
-
Douglas from INVER GROVE, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Faceplate for icemaker fell off, breaking ribbon cable
Ordered new ribbon cable. At first I couldn't figure out how to get the wide end of the ribbon cable off, and I took the whole inner circuit board out - in fact, all it needed was more muscle, a straight pull out, no clips or anything holding it in other than friction. The narrow end attached to the control button board has two clips which pull towards you to loosen the ribbon. Easy install, worked perfectly
Parts Used:
-
Wayne from MARLBOROUGH, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive great stripped for ice eject. Heater bad
Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.
Parts Used:
-
Danny from PUEBLO, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The frame for the meat pan in my Frigidaire refrigerator broke in the middle front, which made opening the drawer a little tricky.
No big deal. I took out the glass in the frame, took out the meat drawer, and removed the broken frame, which doesn't take any tools. After removing the frame, I inserted the new frame, which pops in to two clips in the back, and two in the front on each side. I cleaned the glass and put it into the frame. I re-inserted the drawer into the frame. And VOILA!
Parts Used:
-
Patricia from VICTORVILLE, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drawer was cracked and shelf was broken on one side
No repair needed just replace shelf and drawer
Parts Used:
-
Karin from FAYETTEVILLE, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!