10649212701 Kenmore Refrigerator - Instructions

This story is less about the repair than the service. On Monday, I removed the meat drawer to give it a quick rinse. Unfortunately, I fumbled the ball getting it back to the fridge, dropped the drawer on the hard stone floor, shattering it.

Instead of calling a repair man or going to the local appliance store, I opened up my macbook, found partselect.com, ordered the part and they had it taken care of in 5 minutes. Two days later, Fed Ex handed me a box with the replacement drawer, and I slide it in. Done. Total time to repair -- 6 minutes.

Sure beats leaving the house!

I followed the procedures that others described that had the same problem,very handy

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

1. Put pieces of wood under door to support it.
2. Unscrew three screws holding door hinge.
3. Disconnect water line.
4. Unscrew screw holding each cam. One to door and one to hinge.
5 Replace cams.
6. Retrieve plate with threaded holes behind frame that the hinge attaches to.
7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.
8. Replace all three hinge screws.
9. Connect water line fitting.
10. Remove wood for door support.
11. Check door for smooth movement and strong pressure when closed.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

Emptied door of food jars etc. Used socked on top plate. Removed door and placed on a flat surface. Used socket to take out cam on the bottom of the door. Replaced worn cam. Replaced nylon sleeve on the top of the refrigerator door with needle nose pliers. Placed door in the bootom slot with the new cam in place. Placed top plate in the new nylon sleeve on the door. Replaced screws with socket wrench.

From the Expanded view on the website, I chose the bin -I thought. The expanded view picture is too small and I got the shelf instead. -But a phone call got everything back on track.
Repair involved a knife to open the box!

Simply slid out damaged shelf and slid in new one

First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!

I watched the repair video and did exactly as described. Excellent video and step by step instructions. Follow them and you cannot go wrong.

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

Took out old drawers, slide new drawers in.