Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
BRIAN D - February 24, 2022
Verified Purchase
Replacement inner door panel.
Part arrived in three days and worked perfectly. Easy repair and excellent service
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 1.3 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Rubber seal (boot) needed to be replaced.
I began by removing the seal from the exterior lip of the machine housing. I took a razor and removed any rubber and adhesive that remained on the unit.
Next, I remove the boot from the soap dispenser tube (located at about 11:00 of the opening) with a needlenose plyers. The manual recommends flattening a 3" copper pipe to fashon a tool to release the "bread tie" fastener. I can see why but patience with a needlenose sufficed.
I pulled the boot down from the tub housing (with much force) exposing the band that holds the boot in firmly. I one pull, both pieces came out. I could tell getting the new one is was going to be a chore.
I cleaned the area and after about 40 strenuous minutes of getting the new boot onto the tub, only a couple things remained. Even with help, be prepared to dedicate hours of frustration getting the band around the boot securing it to the tub. The working space is minimal and the task is virtually hopeless to slightly possible.
Once that's taken care of, you may feel like you can accomplish anything. The rest goes up in the order it came out. Make sure you slide the boot up as far up the soap dispensing unit as possible before securing the bread tie clamp.
Run the seal around, close the door and have one of you kids clean up the work area (and mop the blood, sweat and tears from the unit and the floor.
Other Parts Used:
Jon from Stevens Point, WI
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
10 of 23 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
K
July 16, 2019
Plastic on the door cracked and broke away from the screws on the hinge. Is this door easy to take apart, add new part, then place back on the hinge? If it does not work, is the part returnable?
For model number 417 47102700
Hello,
Thank you for your question. Before you begin any repair please unplug the appliance from the electrical outlet or turn the circuit breaker off. Before you remove the door from the washer place a towel on top of the washer so you may set the door on top of it. Then open the door so you can take it off. Use a number 2 square driver to remove the screws securing the hinge to the door. When you are removing the upper screw, hold onto the bottom of the door so it does not hang and drop. Once the screws have been removed, place the door on top of the washer. To remove the hinge, you will need to remove the bellow to access behind the front panel. There is a spring at the bottom of the bellow, where you will need a flat head screwdriver to get behind it and then you can pull the clamp off of the bellow. Then remove the bellow from the side where the hinge is fastened and use the screwdriver to remove the screws securing the hinge. To remove the inner door panel, you will need to remove all 4 screws. Remove the screws securing the door strike first and set the strike aside. Then remove the other 2 screws. With the screws removed, lift the door up and use a flat head screwdriver and pry in between the panels where the door latch was attached. Carefully pry the panels apart. Once you have it split, run the screwdriver around the door to separate the 2 panels. In some models where the hinge attaches to the door, that section is glued and once you pry the panels apart, you will need to cut that area. You will need to use a hack saw blade. Once it is cut you can pull the panels apart. Then set the outer door aside and inner door from the glass. Use a flathead screwdriver to release the tabs securing the glass. Flex them and push down to release them. Once you have a few of the tabs released the inner door panel should drop off the glass. You can now install the new panel. If you have the type of washer where the panels were glued where the hinge is connected, you will need to use some sandpaper to smooth the area where sawed the 2 panels apart so the new panel can be installed correctly. Once this is done, follow the steps in reverse to reinstall the parts. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not start or spin, you may n...
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS975857
Manufacturer Part Number: 134426500