Average Repair Rating: 2.8 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
lower impeller froze to housing and sheared off at shaft - lack of use caused this problem
Removed: tower and spray assembly, pump housing cover, volute cover, nylon retainer, lower impeller, sleeve and seal assembly. Replaced the sleeve and seal assembly and then the impeller. Reassembled. The small, square hole, nylon retainer was not shown in the diagram and it took me a while to recognize that it had to slip off the shaft before the broken impeller and sleeve and seal assembly could be removed. That was the trick.
Removed the rack out of dishwasher. Removed sprayer by removing 4 screws. Removed cover to pump propeller assy.by just lifting up on the cover. Then you remove 4 screws from the pump cover. Remove the propeller. Pull up on shaft and seal. Then when you replace everything just reverse the directions.
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
January 14, 2020
How do you remove the top motor seal from the shaft? There looks like a plastic ring above seal but it will not come off.
For model number FDR252RBS1
Hi James,
Thank you for your question. To remove the seal from the shaft, first remove the tower by turning it counterclockwise from the spray arm. Then, remove the 3/8-inch nut that holds the arm to the diffuser. You will then need to remove the diffuser by removing the 4-5/16-inch bolts that holds the diffuser to the sump plate. Then remove the upper wash impeller by unthreading the T-25 Torx screw holding it in place. Then remove the macerator blade from shaft and then remove the pump housing cover. You will then need to remove pump slinger and the volute cover. To remove the volute cover you will need to unthread the 2 T-20 Torx screws holding it in place. Then you will need to remove the lower pump impeller. Then remove the carbon face half of pump seal. The motor shaft seal will come mounted on a sleeve. This protects the seal surfaces. This sleeve must be removed to install the new seal. Check seal faces to be sure they are both clean and free of any debris. Install ceramic half of seal into sump. Make sure it bottoms out in sump. Slide the top half of the seal onto motor shaft and make sure that it is fitted correctly and is tightly in place and everything matches correctly. The old plastic sleeve may be stuck on the motor shaft and you will need to pry it off. Be careful not to damage the housing or the shaft. We hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Gord
September 18, 2021
I found that it is leaking from the bolts underneath
For model number FDR251RJS0
Hello Gord, thank you for writing. You should check the Water Inlet Valve PartSelect Number PS1990907. And, the Inlet Tubing PartSelect Number PS12746654. We have attached a video for you to look at as well. Good luck with your repair.
Hello, My Frigidaire FDR252RBBO dishwasher leaks from the center (trickling down the motor) when operating, and doesn't drain properly at the end of the cycle. I found that replacing the motor seal and sleeve (PS421123) may fix these problems. On your website it says that I may also need a new lower drain impeller. How would I know if I need to replace the impeller, too, and how do these two parts work together?
Thanks, Peter
For model number FDR252RBBO
Hello Peter, thank you for your inquiry. We have researched your model and found that if it is not draining properly, then you may need to check its drain hose, part number PS9494138, if it is fine then the impeller, part number PS420969, is probably causing the dishwasher to not drain properly. Leakage from the center of the dishwasher can be fixed by replacing Motor Seal and Sleeve Kit, part number PS421123. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS421123
Manufacturer Part Number: 154387601