![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
FORK SUPPORT Assembly
Fits your GTUP240GM4WW!
$94.76
Special Order
Fits your GTUP240GM4WW!
PartSelect Number
PS3501444
Manufacturer Part Number
WH16X10147
Manufactured by
GE
Troubleshooting
This part works with the following products:
Washer Dryer Combo.
This part works with the following products:
General Electric, Kenmore.
Customer Repair Stories
Average Repair Rating: 1.0 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Tub seal leaking, hub nut stuck, tub stuck.
If you're handy with a right angle grinder and a cutoff wheel, it can be done.
Order the washer hub, hub nut, and the spring washer above the hub nut.
Get the agitator out. a pair of flat bars and some hammering on the agitator retaining bolt helps a lot. Loosen the retaining nut a few turns, pry and hammer at the same time, repeat until he agitator comes out.
On the bottom of the tub assembly is a brown plastic bracket that holds the spin solenoid. Remove it before you dismount the tub assembly. It's easy to break, and it costs $65.
Dismount the tub assembly from the cabinet. Turn it over and remove the motor. Unbolt everything that can be unbolted. Cut away enough of the large metal plate that was bolted to the bottom of the tub so that the tub assembly will stand upright on a five gallon bucket.
Stand the tub assembly upright on the five gallon bucket. Cut away the hub nut. Try not to cut into the black steel disk on the bottom of the tub. Soak the metal parts with PB Blaster, Kroil, or similar. Slip a three foot long piece of 1 1/4 pipe or conduit over the stem that held the agitator. Hold the pipe upright. Drop a four foot long steel rod into the pipe. Use the steel rod as a slide hammer and whale away. Stop frequently to spray your penetrant, and keep hammering. Eventually you'll drive the old washer hub out of the drum. Remember, everything is plastic and not indestructible..
Before reassembly turn the tub over and clean up the mating surfaces, ditto the agitator. When reassembling use antisieze compound on the mating surfaces.
Order the washer hub, hub nut, and the spring washer above the hub nut.
Get the agitator out. a pair of flat bars and some hammering on the agitator retaining bolt helps a lot. Loosen the retaining nut a few turns, pry and hammer at the same time, repeat until he agitator comes out.
On the bottom of the tub assembly is a brown plastic bracket that holds the spin solenoid. Remove it before you dismount the tub assembly. It's easy to break, and it costs $65.
Dismount the tub assembly from the cabinet. Turn it over and remove the motor. Unbolt everything that can be unbolted. Cut away enough of the large metal plate that was bolted to the bottom of the tub so that the tub assembly will stand upright on a five gallon bucket.
Stand the tub assembly upright on the five gallon bucket. Cut away the hub nut. Try not to cut into the black steel disk on the bottom of the tub. Soak the metal parts with PB Blaster, Kroil, or similar. Slip a three foot long piece of 1 1/4 pipe or conduit over the stem that held the agitator. Hold the pipe upright. Drop a four foot long steel rod into the pipe. Use the steel rod as a slide hammer and whale away. Stop frequently to spray your penetrant, and keep hammering. Eventually you'll drive the old washer hub out of the drum. Remember, everything is plastic and not indestructible..
Before reassembly turn the tub over and clean up the mating surfaces, ditto the agitator. When reassembling use antisieze compound on the mating surfaces.
Other Parts Used:
-
David from ABINGDON, IL
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Socket set, Wrench (Adjustable), Wrench set
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Eugene
November 14, 2017
The washer goes through wash and rinse cycles and drains. The issue is when it goes to the spin cycle the motor spins but the belt does not turn the drum. What is the culprit?Thanks in advance for your help
For model number GTUN275EM2WW
Hi Eugene, Thank you for the question. If the motor is running but the belt is not turning I suggest replacing the belt.PartSelect Number: PS1766009. It can become stretched and wore out over time and need to be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3501444
Manufacturer Part Number: WH16X10147
Manufacturer Part Number: WH16X10147
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)