Product Description
Door Stop - Black Specifications
This is the replacement door stop, also known as a door stop bracket, for your refrigerator. It is made of black plastic, and is approximately 3 inches long and 1 inch wide. The door stop bracket stops the door from opening more than approximately 90 degrees. The stop can occasionally break, and this will allow the door to open more than 90 degrees. When this occurs, you will need to replace the door stop. This part is sold individually and is an OEM part.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Door won’t open or close
This part works with the following products:
Refrigerator.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WR02X13425 replaces these:
AP4926308, 1719741, WR02X10814, WR2X10814
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Faraz B - October 21, 2022
Verified Purchase
Unmentioned size
Since dimensions were not mentioned on the website I thought there is only one standard size available , when i received it unfortunately it was bigger than what i needed.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 5.0 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Fridge Door would not close "automagically"
I had to remove the fridge door (side by side), which took approximately 10min (most of which was retrieving the right size socket wrench from the garage). With the door removed, I could replace the broken door closing cam and door stop... with 4 screws. Not much to it. Had the door mounted back on in another 5min and that was it. :)
Other Parts Used:
-
David from Cary, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
23 of 32 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dorr stop was broken when door was allowed to swing too hard.
I removed the two screws which released the door stop. I then put the new door stop in place and installed the two screws. Job Done.
Other Parts Used:
-
Mark from Frederick, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
17 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My Door Stop Broke
I had to remove 2 screws to get the broken door stop off then I put the new door stop on by using the 2 same screws.
Other Parts Used:
-
M from STERLING HEIGHTS, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Stop Broke on the Refrigerator side.
Followed the instructions in the operator's manual to remove the door. Popped off cover of top hinge. Unscrewed the two screws holding pin down with socket set. Took off door. Unscrewed broken door stop with TORX socket. Replaced new door stop and reversed the process to replace the door. Very simple repair.
Other Parts Used:
-
Peter from Andover, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jan Hull
November 14, 2018
I have the refrigerator "door stop" part no. Ps3487734 for GE refrigerator wr02x13425. Is it necessary to remove the door to install?
Hello Jan, thank you for your question. You don't have to remove the door to do this repair. You can just get on the floor and remove the bolts that hold it into place and reinstall the new one. Good luck with your repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Beverly
February 7, 2020
What tools do i need to install part # ps3487734 door stop
For model number WR02x13425
Hi Beverly. You will need a ratchet with a quarter inch socket and torq 20 driver. Thank you for your question and good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3487734
Manufacturer Part Number: WR02X13425
Manufacturer Part Number: WR02X13425
Brand
Model Number
Description