Average Repair Rating: 4.4 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
push button start/stop not connecting with circuit board
removed the old unit, and simply re-installed the new one-it was very easy
Other Parts Used:
Terry O. from Pietown, NM
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bryce
October 31, 2017
The machine will randomly stop at various points in the cycle. Sometime this happens when we first press the start button and other times at any points in the cycle. It will then have all the lights on much like it is waiting to press start. If you then press start it will start the cycle over after draining. What is the most likely culprit?
For model number GTWN4950L0WS
Hi Bryce, Thank you for the question. Sounds like there is a issue with the timer that controls the cycles. The timer on this model is built into the control board so the board will need to be replaced.Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
December 12, 2017
My washer stops when it gets to the rinse cycle. I can manually rinse cycle and manually spin but it does not automatically do it. Will the control board solve this problem?
For model number GTWN4950L0WS
Hi Mike, Thank you for the question. This is caused by a defective timer switch. The timer on this model is built into the board, so the board Part Number: PS3487291 will need to be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mary
September 25, 2017
I push the start button, all lights across front panel flash on, then all go off except for the 'fill' button. It keeps blinking. No water enters the machine. Will the control board (part #35) most likely remedy the problem? Thank you.
For model number GTWN4950L0WS
Hi Mary,
Thank you for your question. There are a couple of parts that could actually be causing that issue for you. I would suggest checking your pressure switch and your valve as well. Those would be the most likely parts that would cause that issue. You can test them with a multimeter. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Donald Link
October 24, 2019
I have taken the machine apart and the module above the motor blinks 10 time in a row and then repeats. Indicates communication problem, the washer fills but does not agitate or spin.If i move the far right control it will empty. Is that a problem with the system of the control panel or motor assembly
For model number GTWN4250MOWS
Hello Donald, thank you for your question. That is most likely and issue with the board itself. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Craig
December 28, 2017
My washer doesn't fill, sounds like the pump is running to drain. Could this be a board issues or something else?
Hi Craig,
Thank you for your question. If the washer is not filling with water, there are some parts that you will need to check to see which one is causing the issue. You will need to check the inlet hoses and screens, the water inlet valve, the lid switch, the select switch or water temperature switch if present, the water level pressure switch if present and the timer or electronic control board. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Mohamed
February 26, 2019
My start button does not work everything is fine and the leds are ok
For model number GTWN4450MWS
Hello Mohamed, Thank you for the question. If the rubber button is not damaged you will need to replace the start switch. The switch is built into the board, PartSelect Number PS3487291. Unfortunately the board will need to be replaced. Hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3487291
Manufacturer Part Number: WH12X10475