Ice Bucket Seal
Fits your 36358475894!
$16.64
Special Order
Fits your 36358475894!
PartSelect Number
PS298716
Manufacturer Part Number
WR2X7905
Manufactured by
GE
Troubleshooting
This part works with the following products:
Refrigerator.
This part works with the following products:
General Electric, Kenmore, Hotpoint, RCA.
Part# WR2X7905 replaces these:
AP2059747, 298189, WR02X4149, WR02X7905, WR2X4149
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
meatal parts were rusted
the part is fairly easy to take apart, however pay close attention to how things fit and go together. It took me sometime to figure the reassembly out due to my lack of close attention to taking it apart. other than that it is simple.
Other Parts Used:
-
Allan from Pleasanton, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
26 of 45 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bucket drive shaft disengaged from motor drive
This is a 25 year old unit. The ice bucket had warped over time causing the face plate to move forward of its ideal position pulling the entire assembly out of the drive. Removed dispensing unit face assembly. Removed drive shaft assembly. Replaced all washers. Reversed old broken drive cup. Married old drive cup to new drive cup...lining up drive slots. Drilled 6 ea. 3mm holes evenly spaced around circumference into the face of the old drive cup. Fastened drive cups together in vice and with C clamp...then using phillips head screws installed 3 ea. from opposing entry points on each side of this homemade shaft extender. This "mechanism" increased the effective length of the dispensing shaft assembly allowing for a proper fit of the drive shaft to the motor drive connection. Unit now works perfectly. Total cost @ $40.00 and two hours work which would have taken less than one hour if I had remembered to install the ice bucket seal the first time. New ice bucket would have cost @ $185.00. Home warranty does not cover ice makers or any of the associated parts. DIY...it isn't that difficult.
Other Parts Used:
-
Paul from Ashton, MD
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers
12 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
original ice bucket had a broken auger guide
the parts arrived the next day!!! Awesome.
Detached the original bucket from the dispenser face plate by removing all screws. Must remember where all the screws go. Attached new bucket to original dispenser face plate. Very easy.
Detached the original bucket from the dispenser face plate by removing all screws. Must remember where all the screws go. Attached new bucket to original dispenser face plate. Very easy.
Other Parts Used:
-
harvey from shawnee, KS
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rusty and broken plastic parts
It was just a matter of replacing the broken parts, and reassembling the ice machine. Nothing too difficult.
Other Parts Used:
-
Jorge from Aventura, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Earl
November 12, 2019
The ice maker auger will not stay in the back support cup. I just purchased your part number wr2x7905 after looking at diagrams and getting a recommendation. But alas, this seems to be the bucket support at the outside end.What can I get to make the auger stay in place in the rear of bucket where it connects to the drive bar?
For model number TBX25RLG
Hello Earl, Thank you for the question. I suggest changing the Ice Dispensing Drive Cup, PartSelect Number PS297895. It could be worn and not holding the auger. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Rocco
July 5, 2021
How does this rubber piece attach to the rear of the ice maker
For model number Part number ps298716
Hello Rocco, Thank you for the question. The Seal just slips onto the lip of the Ice Bucket. The Lip of the bucket fits into the Channel of the Seal. We hope this helps!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS298716
Manufacturer Part Number: WR2X7905
Manufacturer Part Number: WR2X7905
Brand
Model Number
Description
Kenmore
36358072893
Refrigerator
- Kenmore Refrigerator Model 363.58072893 (36358072893, 363 58072893) Parts