Part Location Diagram of WH01X10088 GE Start/Stop Button
See part 21 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Start/Stop Button

★★★★★
★★★★★
1 Review
$24.06
  Special Order
PartSelect Number PS268476
Manufacturer Part Number WH01X10088
Manufactured by GE
Product Description

Start/Stop Button Specifications

This is the start/stop button for your washer. If your washer will not start after the button is depressed, you may need to replace it. However, you may also want to check your door switch, because when the washer will not start, the door switch is often the issue. This part is made of rubber and is gray in color. It is a little bigger than 1 inch in diameter and is sold individually.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start | Touchpad does not respond
This part works with the following products:
Washer.
This part works with the following products:
General Electric.
Part# WH01X10088 replaces these:
AP3661155, 877584, WH01X10032, WH12X10140, WH1X10032, WH1X10088
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 5.0 / 5.0, 4 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
dryer cycle switch broke/washer pressure switch
took screws out of panel back and replaced items one wire at a time. real simple to do
Other Parts Used:
Timer SWITCH PRESSURE
  • Jerald from San Antonio, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
58 of 113 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would not start
used pliers to grip and remove old button cover, used small screwdriver to push around the edge of new cover.
Other Parts Used:
  • C.W. from NAHUNTA, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
9 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not start ,or delayed after multiple times trying.
Removed knobs ,removed screws on back plate , removed. Back plate ,played plate on top of washer after putting a towel down to keep scratching, disconecte wireing replaced both boards and reverse instructions. Pushed button and it started right up.vidio was very helpful .
Other Parts Used:
  • Daniel from HENDERSON, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Button was worn out.
Replaced the button and was working in less than Fifteen Minutes.
Other Parts Used:
  • Emmett from COLCORD, WV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

16 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Corey
August 25, 2017
All lights work. Pushing start button will not turn on washer. I've been having to push much harder recently....is it the button or the switch on the circuit board?
For model number WCSE4160B2WW
PartSelect logo
Hi Corey, Thank you for your question. I would suggest checking the door switch to see if it is working correctly. If it is alright, then you may need to replaced your control board. The button is just a small rubber piece. I hope this helps. Good luck with your repair.

17 people found this helpful.

Was this helpful?
Thank you for voting!
Ro
May 17, 2019
Top loaser washer, at times, i have to press the start button a few times for the cycle to begin. What would be the cause of this?
For model number GTWN4250D
PartSelect logo
Hello Ro, Thank you for the question. This sounds like the switch behind the push button is defective. The switch is made as part of the Electronic Control Board, PartSelect Number PS8757105. Thank you for your inquiry, good luck with this repair!

10 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Becky
July 22, 2019
How is "start/stop" button removed and replaced?
For model number WJSE4150B1WW
PartSelect logo
Hello Becky, thank you for your question. This is a very easy repair. The button is a small rubber piece that has a lip around the edge. The easiest way to replace this is to use pliers to grip and remove old button cover, then use a small screwdriver to push around the edge of new cover. Be careful not to push too far into the hole as there are electronic boards behind that button and in the control panel. I hope this helps!

7 people found this helpful.

Was this helpful?
Thank you for voting!
Brenda
August 8, 2019
When i push start button, it starts and then stops, if i push another time it will sometime start. Sometimes it stops with first push but often does not. What part do i need? Thanks.
For model number GTWN4250D1WS
PartSelect logo
HI Brenda, thank you for your question. You should take a look at your lid switch being the issue. If it is not then the issue is likely in your control board. Good luck with your repair.

4 people found this helpful.

Was this helpful?
Thank you for voting!
Virginia
July 16, 2021
After a few years, the start/start switch now remains depressed into the frame and the machine will start a new cycle after completing one unless i unplug the machine. I've pulled the start/start button out with a screwdriver, but it took me 20 min. I can't do that every time i wash. Should the button be replaced or should i remove the back panel and adjust the original button?
PartSelect logo
Hi Virginia, Thank you for your question. You can try repositioning the start button, but if it will not stay in place, you will need to replace it. We hope this helps! Good luck with the repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Ron
August 22, 2017
Will not start or fill up with water could you wire across start switch to check it?
For model number gtwn4950lows
PartSelect logo
Hello Ron, thank you for contacting us. This could be a few different things. If your washer won't fill, check the hot and cold faucets to make sure they're both turned on fully. GE washers require water pressure between 10 and 120 pounds per square inch. Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks. If the problem persists, turn off the water and remove the fill hoses. Check the filter screen inside the hoses, and clean them with a brush or toothpick if needed. Also, an improperly closed lid is a common problem that prevents the washing cycle from starting or completing, so always make sure you close the lid to your GE washer tightly. Mechanical GE models have a lid switch probe -- a small piece of plastic that fits into a hole under the lid; if this is knocked out, the machine won't start once the lid is closed. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Ardis
July 31, 2019
Washer will not start when i press the start button. Took it apart and it still will not work when mechanism depressed.Please advise.
For model number WJRE5550K2WW
PartSelect logo
Hi Ardis, thank you for your question. There are a number of parts that could cause the issue. First you should take a look at your lid switch. That part will not allow the appliance to start normally if it believes that the lid is open. If that part is fine however, then the issue might actually be in your control board itself. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
John
April 4, 2019
This is a GE front load dryer and when it's started for the first time today the push to start button lights up and works fine sometimes you can do this multiple times and it's ok if it runs approx.5 mins we open the door check the clothes and close the door push the button it won't start do this about 5 20 times and it will start,is it my push to start switch that is defective??
For model number DBVH52OEJ2WW
PartSelect logo
Hello John, thank you for your question. We would recommend testing the following parts to determine what the issue is. The parts are - Interlock Switch Part Number: WD21X10261, High Limit Thermostat - L315-65 Part Number: WE4M137, Inlet Control Thermostat Part Number: WE4M398 and Safety Thermostat Part Number: WE4M160. If these parts are tested and are functioning correctly the issue could be the electronic board or motor. The start switch is part of the electronic control board.

1 person found this helpful.

Was this helpful?
Thank you for voting!
John
April 4, 2019
Hi this is john again about the GE front load dryer, I forgot to mention one other thing when it don't want to start while depressing the start button I hear a clicking sound, I'm sorry I forgot to mention that and once again thank you.
For model number DBVH520EJ2WW
PartSelect logo
Hello John, Thank you for the information. We still suggest testing the same parts, but this does point more towards a defective motor. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Doretha
November 18, 2017
The timing seems off when I start the machine, it starts to fill and then stops. Sometimes it fills and gets to the wash cycle then stops. I have to keep pushing start button to get through all the cycles. If that does not work I have to drain and spin, then start the cycle over again. Any suggestions?
For model number WJRE5500G1WW
PartSelect logo
Hello Doretha, Thanks for your question. You will want to first check the lid switch assembly, part number PS1482372, for continuity by using a multi-meter. If it does not test properly, replace it. Next, try testing the water inlet valve, part number PS1155105, for continuity and replace it if it does not show any. Lastly, consider replacing the control board (part number PS2351829) if both the water inlet valve and lid switch are testing properly. I hope this helps.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
  • 2
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS268476
Manufacturer Part Number: WH01X10088
Brand
Model Number
Description
General Electric
57281B0WW
Washer
General Electric
57281B1WW
Washer
General Electric
57281B3WW
Washer
General Electric
57281B5WW
Washer
General Electric
57481D0WW
Washer
General Electric
57481D1WW
Washer
General Electric
57481DCWW
Washer
General Electric
57491D0WW
Washer
General Electric
57491D1WW
Washer
General Electric
57751H0WW
Washer
General Electric
57751H1WW
General Electric
57751H2WW
General Electric
57751H3WW
Washer
General Electric
58971K0WW
General Electric
58971K2WW
Washer
General Electric
58971K3WW
Washer
General Electric
EWA2000A0WW
Washer
General Electric
EWA2500A0WW
Washer - WASHER
General Electric
EWA3000B0WW
Washer
General Electric
EWA3000B1WW
Washer
General Electric
EWA3000B2WW
Washer
General Electric
EWA4500D0WW
Washer
General Electric
EWA4500D1WW
General Electric
EWA4500DCWW
General Electric
EWA5000D0WW
Washer
General Electric
EWA5600G0WW
Washer
General Electric
EWA5600G1WW
Washer
General Electric
EWA5600G2WW
Washer
General Electric
EWA5600G3WW
Washer
General Electric
EWA5600K0WW
Washer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service