Timer - 60Hz
Fits your 36314031001!
$232.68
Special Order
Fits your 36314031001!
PartSelect Number
PS260132
Manufacturer Part Number
WD21X10077
Manufactured by
GE
Product Description
Timer - 60Hz Specifications
The purpose of a dishwasher timer is to control the unit's cycles by regulating the length of time that power is directed to each component.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric, Kenmore, Hotpoint.
Part# WD21X10077 replaces these:
AP2039748, 824338, 165D4779P105, WD21X10103
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ed
November 5, 2018
Dw only allows water into the tub on the water saver setting-not the the first 2 settings on the dial? Is this correct for this model??
For model number Hotpoint HDA3200F01
Hello Ed, thank you for your question. Yes, the timer part number WD21X10077 is the correct timer for your unit. If some of the cycles aren't working but others are, the timer is the most likely issue. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bill
January 12, 2020
When i unlock door washer wont turn off. Must tap the front to stop. Would this be the timer
For model number gsd2000fo1wh
Hello Bill and thank you for writing.
It certainly sounds more like it could be a faulty interlock switch PS1481922 and/or a faulty door latch PS259293, you should check for signs of damage, and replace if necessary. We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
Related Parts:
Duane
February 10, 2020
The dishwasher comes on fills with water and i move the dial forward slightly and it begins to wash. The dial doesn't move . If i move it by hand it will click and began to drain.Question- should the dial move forward automatically when washer is turned on?
For model number 36315171000
Good Day Duane. Thank you for your question in regards to your unit (Model Number 36315171000). Based on our research, you may need to replace the Timer (PartSelect Number PS260132) in order to solve this issue. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
Was this helpful?
Thank you for voting!
Ryan
August 19, 2021
Hello,
During the dishwashing cycle, sometimes the dishwasher will drain and the drain solenoid will stay open when the dishwasher tries refilling with water (when normally the drain solenoid will close before refilling). i first inspected the drain solenoid, which looked badly corroded and dirty from a bad drain valve shaft seal, which leaked dirty water onto the solenoid and made the plunger very tight in the solenoid. i replaced the drain valve shaft seal/push on nut and the entire solenoid kit with all new parts.
i'm getting essentially the same result as before i replaced the solenoid-related parts. the solenoid seems to consistently behave properly only on certain drains of the entire cycle, and likewise misbehave on certain other drains during the entire cycle. i'm no expert, but it seems like the solenoid is getting signaled to drain on certain specific drains, but not getting signaled to drain on other drains.
any thoughts? does the timer regulate the signals to the drain solenoid? i checked the timer cam as well and it looks like there is no damage.
thank you.
For model number GSD2230F01WW
Hi Ryan,
Thank you for your question. If your washer is filling and draining at the same time, check the drain solenoid. When the dishwasher drains, the plunger is pulled down causing the drain flapper to open and allow the water to drain. Verify if the plunger is stuck in the down position. If not, the problem may lie with the spring and the linkage connected to it. These parts are found in the drain solenoid kit, part number PS260117. If you need to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS260132
Manufacturer Part Number: WD21X10077
Manufacturer Part Number: WD21X10077
Brand
Model Number
Description