Glass Turntable Coupler
Fits your JVM1870SF02!
$23.68
Special Order
Fits your JVM1870SF02!
PartSelect Number
PS227859
Manufacturer Part Number
WB06X10144
Manufactured by
GE
Product Description
Glass Turntable Coupler Specifications
This part accepts a D-shaped motor shaft.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Tray won’t turn
This part works with the following products:
Microwave.
This part works with the following products:
General Electric, Hotpoint.
Part# WB06X10144 replaces these:
AP2016754, 769278, WB6X10144
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 17 reviews.
What's this?
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Carousel tray drive coupler broke
This coupler has a tab on it that keeps you from being able to push it straight down onto the motor from the inside of the microwave.
Turn off the breaker to the microwave or unplug it. Remove five screws that hold the bottom cover of the microwave. The cover will hinge down and hang on tabs at the back.
Unplug the wire connector on the drive motor by pulling it straight off. Remove one screw that locks the drive motor in place. Turn the motor slightly to unlatch it from its mounting tabs.
Place the new coupler into the opening inside the microwave. While holding/turning the coupling with one hand, insert the motor shaft into the coupling. It will only fit one way. Press the motor and coupling together until the motor can be latched into its mounting tabs. Secure motor with screw and install bottom cover.
Turn off the breaker to the microwave or unplug it. Remove five screws that hold the bottom cover of the microwave. The cover will hinge down and hang on tabs at the back.
Unplug the wire connector on the drive motor by pulling it straight off. Remove one screw that locks the drive motor in place. Turn the motor slightly to unlatch it from its mounting tabs.
Place the new coupler into the opening inside the microwave. While holding/turning the coupling with one hand, insert the motor shaft into the coupling. It will only fit one way. Press the motor and coupling together until the motor can be latched into its mounting tabs. Secure motor with screw and install bottom cover.
Other Parts Used:
-
BRIAN from PERRY, OK
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
59 of 73 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken coupler
After lifting the glass turn plate, I just pulled out the plastic coupler that turns the plate. A piece just broke off underneath for no apparent reason so it couldn't turn the plate. I put on the new one and it works fine.
Other Parts Used:
-
Bob from Mesa, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
18 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Glass turntable stoped turning due to broken coupler
Pulled out broken one with fingers, put on new one with fingers, it did not have anything preventing it from just slipping on. Didn't need to take anything apart to install me part.
Other Parts Used:
-
Barbara from Fruit Heights, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
10 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable coupler became brittle and fractured
I simply pulled the old coupler off the moter shaft after removing glass turntable plate. The coupler lifted right out since it was fractured. Luckily all peices came out attached. Typically you would need to remove the bottom access panel on the microwave and remove the turntable motor to install the new coupler. However you can simply snap off the extra plastic piece that is molded to the coupler to allow for an easy push down onto the shaft from the inside of the microwave cooking area where the coupler fits onto the moter. Piece of cake. I don't believe there is any danger in shortcutting this because the weight of the glass plate will hold it in place.
Other Parts Used:
-
Timothy from Clarksville, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
9 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coupler was broken
removed the broken coupler and replaced it with the new one.
Other Parts Used:
-
Maria from Edison, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
9 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable quit turning.
Disconnected power cord from receptacle. Removed 5 screws in bottom panel and allowed it to swing downward on rear hinged edge. Disconnnected power wires to motor. Removed screw to detach motor. Inserted coupler through hole beneath center of turntable. Inserted motor shaft into coupler and re-attached motor. Connected power wires to motor and then closed the bottom panel and re-inserted the 5 screws.
Other Parts Used:
-
JACK from ETOWAH, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable wouldn’t turn
I removed a few (6) screws and disengaged the motor. Removed the parts and installed in reverse order. Replaced the screws. Easy
Cleaning up the grease from cooking for years on the stovetop below took WAY longer. But the repair was simple!!
Cleaning up the grease from cooking for years on the stovetop below took WAY longer. But the repair was simple!!
Other Parts Used:
-
Kim from Richland, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable coupler broke
I took the part out of the box and handed it to my wife and said "here ya go hun, go put this under the glass turntable in the microwave. You'll know it's installed when you hear it click down" She yelled back, "easy as pie" - - - Humm.. I can't make a pie. Fortunately the old one was in one piece as the side just split so it slid off very easy. The new one just snapped in place.
Other Parts Used:
-
Thomas from Savannah, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable coupler bore became oversized.
Small sized phillips screw driver was required. Once gaining access to the new motor the part(s) replacement was simple.
Other Parts Used:
-
Walter from Herndon, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud noise from the Microwave and the tray was not truning
I followed the directions on your web site. I removed the screws adn dropped the bottom tray, unplugged the drive motor, removed two screw, and replaced with the new motor. It only took about 15 minutes.
Other Parts Used:
-
LEN from OCEAN SPRINGS, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- 2
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bernard
January 4, 2023
Ordered the wrong GE Microwave model (1853SJ02) turntable coupler. How can I return and reorder correct piece
Hello Bernard, thank you for your question! The compatible coupler for your model is part number PS227859. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Martin
September 5, 2019
Will not turn
For model number jvm1840wd001
Hello Martin, Thank you for the question. If there is no damage to the Glass Turntable Coupler, PartSelect Number PS227859 I suggest replacing the Drive Motor, PartSelect Number PS237772. Hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS227859
Manufacturer Part Number: WB06X10144
Manufacturer Part Number: WB06X10144
Brand
Model Number
Description