Burner Gasket
Fits your JGP940SEK5SS Cooktop!
$14.97
Special Order
Fits your JGP940SEK5SS Cooktop!
PartSelect Number
PS227129
Manufacturer Part Number
WB04T10012
Manufactured by
GE
Troubleshooting
This part works with the following products:
Range, Cooktop.
This part works with the following products:
General Electric, Kenmore.
Part# WB04T10012 replaces these:
AP3668639, 874235, WB4T10012
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 2 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No spark at one burner
Other writers have claimed that this is a "really easy" job. They apparently had one or more of: 1. Less used appliance. 2. Never spilled anything on the cooktop 3. Much better luck. In my case, the apparently faulty igniter absolutely would not pull out. I removed it by removing the burner retaining screws and prying under the burner casting. Having done that, I cleaned the igniter and tested it again. None of the igniters worked, and I could hear arcing under the cooktop, indicating one or more of the igniter HV wires had somehow grounded. After a fruitless search for instructions on raising the cooktop, I stumbled upon an envelope glued to the back of the range that told me to remove all four burners and igniters and to release the cooktop by inserting a thin screwdriver under the front edge about 3" from each end to release the spring clips. Several of the igniters were cemented in place with caramelized sugar and required some pretty vigorous prying to dislodge. If I had this to do again on a range that had been ridden hard, I wouldproactively order a full set of gaskets (they're fragile), the HV harness (even if it doesn't leak as mine did, the igniter connectors degrade from heat exposure), a set of electrode mounting clips (none of them were much use either), and enough igniters to replace any that don't work plus at least one. I pried out the recalcitrant igniters; in retrospect I should have crushed them because of the severe risk imposed by prying of breaking either a burner casting or the cooktop -- either of which are far more expensive than another igniter.
Other Parts Used:
-
Michael from Weatogue, CT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
43 of 59 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two igniters inoperable due to bad igniter switches
There are already some very good instructions for this repair on the website - I followed them as written. I recommend going through the instructions carefully first to make sure you have everything you will need and so you know what to expect. Also, if practical I recommend you do the disassembly before ordering the parts so you know exactly what you need. A couple of burner gaskets got messed up during disassembly, so I decided to replace them and ordered a couple along with the harness assembly. A couple of the igniters were difficult to disconnect from the wiring and I was afraid I was going to break some, but managed to get them off intact. The replacement harness assembly didn't look just like the old one that I removed and at first I thought I'd have to exchange it. Check the paper that comes in the box with the harness and it will show how the new one goes on. Everything went back together easily and all igniters are operating.
Other Parts Used:
-
Robert from HARRISON CITY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS227129
Manufacturer Part Number: WB04T10012
Manufacturer Part Number: WB04T10012
Brand
Model Number
Description