Relay and Overload Kit
Fits your MSD2422GRW!
$142.47
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your MSD2422GRW!
PartSelect Number
PS2004059
Manufacturer Part Number
12002784
Manufactured by
Whirlpool
Product Description
Relay and Overload Kit Specifications
This part helps protect the motor from overheating.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Freezer section too warm | Fridge too warm
This part works with the following products:
Refrigerator.
This part works with the following products:
Maytag, Jenn-Air, Crosley, Amana.
Part# 12002784 replaces these:
AP4009660, 1194899, 12002784, 12002784, 61005271, 61005616
Customer Repair Stories
Average Repair Rating: 3.6 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Refrigerator
Removed back cover by removing 6 screws, vacuumed the dust out to make it less unpleasant and made sure I had the fridge far enough away from the wall to easily see. The kit was a little different from the relay that was in place - the old one on the compressor was encased in a small plastic carrier, and the replacement was two separate pieces, a short connector wire and a much bigger cover. I made sure the fridge was unplugged, then pulled off the wires (recorded what color went where) and pulled the relay with it's carrier from the compressor. I realized that the carrier was not to be reused, and pushed on the relay and the overload pieces, put on the provided white connector wire, connected the colored wires back to their new connections (orange wire now connects to white connector wire), and carefully snapped the new big cover over the wires and relay. Be careful with the wire routing - don't want to dislodge the connectors when putting on the cover. Remounted the back cover and plugged that puppy in - worked like a champ!
Other Parts Used:
-
Bavo from Lafayette, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
51 of 59 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
doesn't get cold at all and freezer was warm condenser wouldn't run
removed all 6 screws in back of fridge. located the condenser the relay was a white like circut to the left of the unit. The entire pience comes off easy using a flat screw driver to pry it off the pins.
The replacement came in 2 pieces insted of 1.
I replaced the relay and then the overload reconnected the wire harness back the way it was before. The new relay has a larger connector prong for the live wire so the kit comes with a jumper wire so the original wire harness can be used without splitting the cabel made the repair very easy. Also the new capacitor is bigger and better so I replaced that as well. The capacitor makes sure the relay gets stable current so its good to have a working one.
The replacement came in 2 pieces insted of 1.
I replaced the relay and then the overload reconnected the wire harness back the way it was before. The new relay has a larger connector prong for the live wire so the kit comes with a jumper wire so the original wire harness can be used without splitting the cabel made the repair very easy. Also the new capacitor is bigger and better so I replaced that as well. The capacitor makes sure the relay gets stable current so its good to have a working one.
Other Parts Used:
-
Jean from Fremont, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
27 of 31 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The relay had burnt up.
I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.
Other Parts Used:
-
Jacob from Glennville, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
frig got warm, compressor would not turn on, heard clicking noise
googled for answer, deduced relay/switch problem. googled again for parts, found partselect.com, ordered part. 2 days later & $70 lighter, my 8yr old Maytag was working again! Parts were good fit, instructions were decent enough. Not for inexperienced tinkerer though.
Other Parts Used:
-
Jeff from Cherry Hill, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Chris
January 24, 2018
Fridge won't stay on keeps tripping rcd breaker tried another power point through an rcd box and keeps tripping
For model number GC2227GEH1
Hello Chris, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: start relay and overload kit, temperature control thermostat and the main control board. Hope this helps!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2004059
Manufacturer Part Number: 12002784
Manufacturer Part Number: 12002784
Brand
Model Number
Description