![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Troubleshooting
This part works with the following products:
Dishwasher.
This part works with the following products:
Maytag, Amana.
Part# 12002750 replaces these:
AP4010256, 1174058, 12002750, 99002685, 99002686, 99002717, 99002718
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Kevin B - March 28, 2019
Verified Purchase
Easy fix
No tools required.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The vinyl coating on the forward rack of convertible tines dried and cracked away, allowing the steel underneath to rust and deteriorate. It eventually just broke.
After looking the situation over, I decided to remove the entire lower rack and place it on the counter where I could see better. I specified I needed the front tine (part # 24), but received both front and back tines). I used the screwdriver to help slip the old piece out of the plastic clamp end. I broke the end of the first clamp, but fortunately, replacement clamps were also included in the kit. I decided it would be easier to assemble the tines and the clamps first, and then install that into the rack, so I had to remove the other plastic clamp and did so successfully. Then holding the assemblage in place to see just where to snap it into place, I proceeded one clamp at a time and installed it. I kept the new back tine guide just in case someday that one wears out too.
Other Parts Used:
-
Donna from Grand Ledge, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
20 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The front set of convertible tines had begun to rust.
Snapped the old, rusting, tines out of the clips and snapped the new, not yet rusting, tines in. Although the kit includes both sets of tines and replacement clips, I only replaced the one part.
Other Parts Used:
-
Steven from Abingdon, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tines were rusting
I pulled the set of tines that hold the plates off the clips that hold them and pushed the new set into the clips. It was done!
Other Parts Used:
-
Patricia from Nebraska City, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rusted, broken tines
snapped old tines out of plastic guides, snapped new tines in place. Done.
Other Parts Used:
-
Kristine from SEBEWAING, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2004037
Manufacturer Part Number: 12002750
Manufacturer Part Number: 12002750
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)