Product Description
Heating Element Terminal & Insulator Kit Specifications
This kit comes with two ceramic insulators.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Maytag, Kenmore, Amana.
Part# Y304596 replaces these:
AP4290688, 1245904, 3-1122, 3-4596, 301122, 304596, 311070, Y304596, Y311070, Y311071
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Daniel W - December 4, 2018
Verified Purchase
Ceramic part chipped.
The reason i gave a 4 star is because one ceramic piece had a small chip broken of ,but not enough to not be useful. The package was sealed and the piece could be seen through the package. Once installed, i did us epoxy to put the piece in place. So far ,this did not effect the use of the part and was a good fit
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dryer Not Heating
The dryer would run, but not heat up, so nothing was getting dry. I ended up replacing the heating element, and that did the trick. I’ll speak to the repair later, which is not hard. But, it may be more helpful if I share what I did to troubleshoot. Hopefully that saves you from ordering the wrong parts.
First, I verified voltage (240V) at the outlet, then tested each of the thermostats for continuity using my multimeter. They were fine, but when I tested the heating coil it showed open (no continuity). When I removed the coil, I found it was broken about 1/2 way back. So that was all verification I needed.
I made the repair following the video on this site, and they do a great job of walking you through everything. The trickiest part was just taking the slack out of the heating element enough to put the shroud back together. It was cumbersome, but doable. Just gotta work the coil through each insulator to keep it from hanging up as you go. And keep tension on it, without pulling so hard that you stretch the wire. Definitely a good DIY job with only basic tools required.
First, I verified voltage (240V) at the outlet, then tested each of the thermostats for continuity using my multimeter. They were fine, but when I tested the heating coil it showed open (no continuity). When I removed the coil, I found it was broken about 1/2 way back. So that was all verification I needed.
I made the repair following the video on this site, and they do a great job of walking you through everything. The trickiest part was just taking the slack out of the heating element enough to put the shroud back together. It was cumbersome, but doable. Just gotta work the coil through each insulator to keep it from hanging up as you go. And keep tension on it, without pulling so hard that you stretch the wire. Definitely a good DIY job with only basic tools required.
Other Parts Used:
-
Christopher from GLENWOOD SPGS, CO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Darrell
March 6, 2020
This is a Maytag de 212 dryer, serial # 291697 np. I have replaced both thermostats and there is still not enough heat to do a normal load in a normal time. I am going to purchase a new heating coil element to thread through the heater housing (though the old one still looks good), but do i also need these insulator parts?
For model number Maytag DE 212
Hello and thank you for writing.
You should be able to reuse the existing ones, only if the old ones have become damaged you would have to order this kit. We hope this information helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1760665
Manufacturer Part Number: Y304596
Manufacturer Part Number: Y304596
Brand
Model Number
Description