Troubleshooting
This part fixes the following symptoms:
Door won’t close | Door latch failure
This part works with the following products:
Dishwasher.
This part works with the following products:
KitchenAid, Kenmore, Whirlpool, Maytag.
Part# W11612302 replaces these:
8269012, 8534854, W11484017, WP8534854
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Nicole M - April 13, 2023
Verified Purchase
Easy repair, worked as expected
I was shocked at how fast the part came, and very easy to install. We had our dishwasher up and running in no time!
Andrew L - April 28, 2020
Verified Purchase
Perfect fit
Received the part faster than expected. It was just what I needed to stop my dishwasher from leaking.
Michael C - January 14, 2019
Verified Purchase
Easy Repair
Review said 1-2 hours for repair, took me approx 30 mins. Easy to swap out part. Delivery was fast too.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 2 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
A small water leak at door
After replacing broken door cables I had a small leak at the door corner. I replaced door seal with that not fixing the leak and found that the door hinges were bent a little from the cables being broke for awile. Installed new hinges and leak is fixed now. A little difficult but once unit was pulled out about 6 inches the hinges were not bad to replace
Other Parts Used:
-
Tom from UNION GROVE, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
9 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hinge bent went spring cable broke
My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...
Other Parts Used:
-
Timothy from Falls Church, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS16875381
Manufacturer Part Number: W11612302
Manufacturer Part Number: W11612302
Brand
Model Number
Description
Kenmore
66213292K112
Dishwasher
- Kenmore Dishwasher Model 662.13292K112 (66213292K112, 662 13292K112) Parts
Kenmore
66512762K310
Dishwasher
- Kenmore Dishwasher Model 665.12762K310 (66512762K310, 665 12762K310) Parts
Kenmore
66512762K311
Dishwasher
- Kenmore Dishwasher Model 665.12762K311 (66512762K311, 665 12762K311) Parts
Kenmore
66512763K310
Dishwasher
- Kenmore Dishwasher Model 665.12763K310 (66512763K310, 665 12763K310) Parts
Kenmore
66512763K311
Dishwasher
- Kenmore Dishwasher Model 665.12763K311 (66512763K311, 665 12763K311) Parts
Kenmore
66512772K311
Dishwasher
- Kenmore Dishwasher Model 665.12772K311 (66512772K311, 665 12772K311) Parts
Kenmore
66512773K311
Dishwasher
- Kenmore Dishwasher Model 665.12773K311 (66512773K311, 665 12773K311) Parts