Troubleshooting
This part fixes the following symptoms:
Oven is too hot | Little to no heat when baking | Oven not heating evenly | Element will not heat
This part works with the following products:
Range, Wall Oven, Microwave Oven Combo, Microwave.
This part works with the following products:
Frigidaire, Kenmore, Electrolux, Uni.
Part# 5304504897 replaces these:
AP6025829, 318562500
Customer Reviews
Filter By Rating:
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
RICHARD L - February 23, 2023
Verified Purchase
part was accurate and worked perfect
the only issue was it took 7 buisness days to arrive
Edward D - February 4, 2023
Verified Purchase
Oven temp sensor replacement
Everything went well. Part arrived in short order. I replaced the part and the appliance is now working as advertised. All good.
Rick R - January 13, 2022
Verified Purchase
Easy Repair
The part arrived quickly, it was the right one and we were able to change it out very easily. Thanks very much Part Select!
Morley F - November 27, 2021
Verified Purchase
Perfect fit and working fine
Perfect fit and working fine
Pete S - July 13, 2021
Verified Purchase
Easy repair and corrected the problem
Diagnostics indicated that the likely cause of an over temp. on my Frigidaire range was the temperature probe. Part received was exact match to the original, easy install and problem corrected.
Bryce M - March 30, 2021
Verified Purchase
Easy install
Easy to install
Alex L - March 9, 2021
Verified Purchase
TEMPERATURE SENSOR
The part worked and shipping was next day but it did not fix my problem as the temperature in my oven is still dropping after its pre heated. I think it's the control board
Yves L - March 2, 2021
Verified Purchase
Great part
Show up in time great replacement part fit good really happy
Lee W - November 20, 2019
Verified Purchase
simple to order, easy to install, took minutes
Just like the title says!
Bonita M - September 13, 2019
Verified Purchase
IT WORKED!!!
Arrived safely and was easy to install and it worked!!! Great company, easy to order, very efficient company thanks!
- < Prev
- 1
- 2
- Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 3 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Top oven overheating
Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.
Other Parts Used:
-
Ronald from NEVADA, MO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both oven bake and broil elements lost power suddenly at the same time.
Installation of the temparature sensor, one of the technician recommended parts took no time, just two screws and a snap off/snap on part. It did not fix the problem. I then replaced the main control panel, which requires more work, but didn't solce the ussue either. I then replaced the thermal fuse, which wasn't mentioned by tech support, and required much more disassebly of the top panels of the stove, with still no fix to the problem. I am waiting to replace the thermostat heat sensor unit, the only other part in the circuit controlling power supply, requiring removal of the stove top again,
Other Parts Used:
-
Alexander from DELMAR, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
sensor should pull into oven enough to easily unsnap and snap but didn't pull out
on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have
Other Parts Used:
-
Mary from EDGAR, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cyndy
August 22, 2019
Oven only heats to about 150 when using roast or bake i can see the glow from heat source (it is a gas range) but will not heat up. I can turn on broil and it heats up but can’t control temperature
For model number FPGH3077RFB
Hi Cyndy,
Thank you for your question. Thank you for your question. If the oven is not heating correctly, then the issue is likely with the oven sensor, sometimes called the oven thermostat, and you will need to check it with a multimeter. When testing the sensor with a multimeter, the sensor should be tested at room temperature and it should be unplugged from the oven. You will need to measure the resistance between the two prongs at the end of the sensor connector. Replace the oven sensor if the reading is less than 900 Ohms or more than 1200 Ohms. I hope this helps. Thank you and have a great day! I hope this helps. Thank you and have a great day!
11 people found this helpful.
Was this helpful?
Thank you for voting!
Sandra
November 27, 2017
I have tried all your % of problem parts on your website to get my oven to get hot, and nothing has helped, could this part below help? Any suggestions?
For model number FGES3045KFE
Hi Sandra, Thank you for the question. If both elements in the oven are not working at all, I suggest replacing the Control Board,Part Number: PS2368652. If the elements turn on but are not getting hot enough, then replacing the sensor should fix the issue. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Bee
November 19, 2018
F10 is displayed when oven warms up.. is it the sensor
For model number 79040292410
Hello Bee, Thank you for the question. The F10 fault code on your Kenmore oven indicates that the oven has overheated and the most common part replaced is the Temperature Sensor, PartSelect Number: PS11758156. If the sensor did not fix the issue, you may need to replace the control board, Part Number: PS11757779. Thank you for your inquiry, good luck with this repair!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Loal
February 20, 2019
Hi, my wife ran the self clean on our double wall oven, did one then the other right after, the next day the lower did not work and the upper did , i shut off the breaker and pulled out and made sure the thermal switch was good, looked good, when i powered up it switched the lower worked and the upper did not, would it be the circuit board? Sounds electrical, any idea
For model number Kenmore ,fget3065pfd
Hello Loal, Thank you for contacting us. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. I hope that helps. Good luck with your repair
3 people found this helpful.
Was this helpful?
Thank you for voting!
Karen
February 12, 2018
This part at sears is 147.03 dollars. Do you think it is the same part?
For model number 79097313412
Hi Karen, Thank you for the question. Yes, this is the same part. We may order a bigger stock in so we get a better discount on the item, this reflects in the savings we pass onto our customers! Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Amy
December 17, 2018
My oven takes a long time to light. Sometimes it does, and it gets up to temperature, but is slow in doing so. Sometimes it doesn't get up to temperature at all. The broiler works fine, but the bake and convection settings do this. Usually if i go through the preheat button, it heats up but it is slow. Do you think i need the temperature sensor or the ignitor? Would a failing ignitor work sometimes and not all the time?
Hi Amy,
Thank you for your question. If the oven is not heating correctly, then the issue is likely with the oven sensor, sometimes called the oven thermostat, and you will need to check it with a multimeter. When testing the sensor with a multimeter, the sensor should be tested at room temperature and it should be unplugged from the oven. You will need to measure the resistance between the two prongs at the end of the sensor connector. Replace the oven sensor if the reading is less than 900 Ohms or more than 1200 Ohms. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
APRIL
April 3, 2019
Hello - I've noticed my wall oven heats up, but is not holding the temperature. It seems to work well on the convection setting though. Wondering if this could be the part that needs to be replaced....also during initial heat up to 350 temperature spikes 10-15 degrees after sitting at a held temperature for about 1 minute.
For model number FGEW3065KFB
Hello, Thank you for the question. I suggest testing the sensor. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Thank you for your inquiry, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dale
July 31, 2019
On my Electrolux wall unit, must i replace the temperature sensor from the back side of the unit or can i replace it from the front, by reaching into the oven compartment?
For model number EW30EW55GS7
Hi Dale, thank you for your question. There are two ways to do the installation. From the front: https://www.youtube.com/watch?v=hFZlbgMNZAc. And from the back: https://www.youtube.com/watch?v=yTDerTiSW4Y. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dale
July 31, 2019
I encountered an f10 code error (beeping too) during the end of the self-clean cycle. I shut off the breaker to the oven for several minutes. I then turned the breaker back on which cleared the code error and beeping. I turned the oven on and set and started the oven for a baking cycle at 350 degrees - it would not heat up (oven cavity cold to the touch).Will the temperature sensor correct this problem?
For model number EW30EW55GS7
Hi Dale, thank you for your question. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Lori
March 26, 2019
A paper plate went on fire in my Frigidaire microwave, i have no display.I was told that it was probably a temperature sensor. do you agree?
and what is involved to replace?
thank you , lori
For model number Fgmv175qfa
Hi Lori,
Thank you for your question. Most paper plates can be used in the microwave as long as they are microwave safe. You should consult your manual to verify the types of paper plates that you can use and when you buy paper plates check the packaging to see if they are microwave safe. If the display is not working, you will check the touchpad, the electronic control board, the wiring connections between them, the door switches and the fuse. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- 2
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11758156
Manufacturer Part Number: 5304504897
Manufacturer Part Number: 5304504897
Brand
Model Number
Description