![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Product Description
Rear Bearing Specifications
Used in Mixers.
![How Buying OEM Parts Can Save You Time and Money How Buying OEM Parts Can Save You Time and Money](https://img.youtube.com/vi/d6AvOkulk_g/maxresdefault.jpg)
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Mixer.
This part works with the following products:
KitchenAid, Whirlpool.
Part# WPW10170081 replaces these:
AP6016192, 9703570, W10170081
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Mike T - June 30, 2020
Verified Purchase
Fit perfectly
Super fast shipping and part fit great, thanks so much
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Mixer Made Very Bad Grinding Noise, And Would Skip While Making Bread Dough
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Other Parts Used:
-
Dennis from Lake Mills, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
75 of 88 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Removed mixer motor housing by removing 5 obvious screws.
Removed plastic transmission cover by removing 4 obvious screws.
Down load parts exploded drawing from PartSelect.com
Found the worn part by the shiny teeth on the large gear.
Found the large worm gear on the drawing and ordered the gear, and associated bearings. Did not need the seal.
Removed worn part, assembled new gear and beargings in same manner as the worn part, and placed new part in mixer.
Replaced transmission cover gasket.
Repacked grease from transmission cover onto the new gear.
Replaced transmission cover (4 screws).
Replaced mixer motor housing (4 screws).
Replaced mixer trim band around the motor houseing joing. (1 screw).
Plugged it and and it works, good as new.
Removed plastic transmission cover by removing 4 obvious screws.
Down load parts exploded drawing from PartSelect.com
Found the worn part by the shiny teeth on the large gear.
Found the large worm gear on the drawing and ordered the gear, and associated bearings. Did not need the seal.
Removed worn part, assembled new gear and beargings in same manner as the worn part, and placed new part in mixer.
Replaced transmission cover gasket.
Repacked grease from transmission cover onto the new gear.
Replaced transmission cover (4 screws).
Replaced mixer motor housing (4 screws).
Replaced mixer trim band around the motor houseing joing. (1 screw).
Plugged it and and it works, good as new.
Other Parts Used:
-
Stephen from Colorado Springs, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
13 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gears and bearing failure
inspected and replaced worn components
Other Parts Used:
-
Gary from Hamburg, MN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
3 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
noise in trans.
took it apart. more grease all over. Put in all but one gear on the top. The noise is still there going to try to but the old bearings in and try again. I went back to the old worm gear and allmost all the noise stopped. I did put the new bearings in and the other gears. It seems that the gear on the worm gear was cut wrong. The noise was tear able. I tried the different parts I ordered one at a time. To find out which one stopped the noise. Every time I took a part I had grease all over. It took so long every time I put in a new part to put the trans back together again. I had grease all over.
Other Parts Used:
-
Leonard from WORTH, IL
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11749476
Manufacturer Part Number: WPW10170081
Manufacturer Part Number: WPW10170081
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)