Product Description
Water Supply Tube Specifications
This part includes the third level wash spinner.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Not cleaning dishes properly
This part works with the following products:
Dishwasher.
This part works with the following products:
KitchenAid, Kenmore, Whirlpool, Maytag.
Part# WPW10077863 replaces these:
AP6014862, 8268289, 8268359, 8539166, 8558964, 8558965, 8559850, W10077863, WP8558964, WP8559850
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Martin H - April 7, 2020
Verified Purchase
Easy install
I was impressed with the cost and the speed of delivery. We were expecting delays considering the current situation. The part was well protected and was a perfect fit for our dishwasher. The link to the install instructions was appropriate and install was a breeze, actually easier than indicated in the instructions. I will definitely order from Part Select again
Greg P - February 17, 2020
Verified Purchase
Easy repair but didn't solve problem
The part arrived quickly and in great shape. The replacent was easy. The rating is difficult because the part worked great, but I'm left with the same problem as before (obviously I need to try something else).
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 2.7 / 5.0, 2 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water would not drain, upper rack position couldn't be changed
Pulled out dishwasher after checking the air gap, etc. Washer would marginally pump out water and could hear motor running on drain cycle. Usual mess from water draining out of hoses.
Ohmed drain motor at 24ohms, should be 16.3 ohms from repair manual. Noted check valve, a rubber flapper, was canted out from sealing surface.
New motor ohms at 24 ohms, installed new motor prophylactilly. Installed new flapper valve through the sump. Washer checked okay for drain cycle.
Feed tube assembly was ordered as upper rack flapper valve was worn into open on upper position due to normal use. Feed tube spinner was small, so the rubber flapper was scavenged from the new assembly and used on the old feed tube assembly.
Ohmed drain motor at 24ohms, should be 16.3 ohms from repair manual. Noted check valve, a rubber flapper, was canted out from sealing surface.
New motor ohms at 24 ohms, installed new motor prophylactilly. Installed new flapper valve through the sump. Washer checked okay for drain cycle.
Feed tube assembly was ordered as upper rack flapper valve was worn into open on upper position due to normal use. Feed tube spinner was small, so the rubber flapper was scavenged from the new assembly and used on the old feed tube assembly.
Other Parts Used:
-
John from Mountain View, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
57 of 85 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
At the time I ordered the feed tube assembly with spinner and the spray arm seal for the middle wash arm, the problem was dishes not getting clean on the top rack. Two weeks later the dishes were not getting clean on the bottom rack as well as the top rack, and liquid dishwasher detergent was left
I followed the PartSelect video to replace the feed tube assembly with spinner and the spray arm seal for the middle wash arm. Washing performance was better, but a couple weeks later the dishes on the bottom rack suddenly stopped getting clean. I decided I probably needed a new chopper assembly, which is identified by PartSelect as the cause of problem for 48% of the cases of dishes not getting clean. Before ordering the chopper assembly, however, I followed the video about how to replace the chopper assembly to determine whether the chopper assembly seemed to be worn out (the video shown at https://www.partselect.com/PS11722146-Whirlpool-W10083957V-Chopper-Assembly.htm). It was worse than I anticipated. I found the holes of the chopper assembly screen blocked by food, and the spinner in front of the screen had broken apart. In addition to finding the pieces of the broken chopper assembly, I discovered a treasure chest of debris, including about 8 pieces of broken glassware, 3 twister ties, a half-inch button, a 3/4-inch screw, and dozens of small pieces of metal. I poured water into the area and used a kitchen baster to suck out the water with all the pieces of debris, finishing the clean-up with paper towels. I ordered a new chopper assembly to replace the broken one, and the part arrived in under 48 hours. I relied on the same video to install the new chopper assembly. The only tricky challenge was getting the new chopper assembly back into place. I first tried needle nose pliers in two sizes, as recommended in the video, but what worked much better for me was using two chop sticks that were each about 1/4 inch square from top to bottom. Needle nose pliers are slanted, but the chopsticks did not vary in thickness and separated the screen from the spinner an even distance apart, making it easier to get the gear shaft on the chopper assembly to align in a straight line with the gear shaft on the pump motor. I also rotated the two gear shafts so the gears of the chopper assembly would mesh correctly with the gears of the pump motor shaft. The video cannot show that step very well because the man's hand blocks vision of how exactly to fit the chopper assembly into place. The video also fails to warn about possible debris around the chopper assembly and to explain how to clean out the debris. After finishing installing the chopper assembly my 14-year-old dishwasher cleaned my dishes as well as a new dishwasher. I spent a total of $110.24 on parts and shipping and invested a couple of hours total. The alternative would have been to spend $800 on a new dishwasher or wash dishes by hand. I am very, very happy with the outcome.
Other Parts Used:
-
Marilyn Hughes from BOULDER, CO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
8 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kristen
November 6, 2017
How can i tell if it’s broken? There’s a tab inside the top circle that looks like it’s pushed in. How does the tube connect? Does it connect to the top circle or the bottom one?
For model number KUDC10FXSS5
Hi Kristen,
Thank you for your question. Before you begin any repair please unplug the appliance from the electrical outlet or turn the circuit breaker off. Then slide the upper dishrack out of the tracks and then remove the bottom dishrack. Detach the water supply tube assembly from the mounting bracket assembly on the top and the rear of the tub. Rotate the old water supply tube to release it from the pump assembly. Prepare the new water supply tube for installation by transferring the upper wash arm from the old tube to the new one. To do this rotate the locking ring clockwise to release the arm. Remove the locking ring and position it on the new wash arm support with the flat side facing the connector. Align the wash arm on the support and rotate the locking ring counter-clockwise to secure the arm. Now insert the bottom of the new water supply tube into the pump assembly and rotate the tube to secure. Snap the new tube into the mounting brackets on the rear and the top of the tub. Replace the lower dishrack and reposition the upper dishrack onto the track. Your dishwasher is now ready to use again. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11748132
Manufacturer Part Number: WPW10077863
Manufacturer Part Number: WPW10077863
Brand
Model Number
Description