Average Repair Rating: 4.2 / 5.0, 3 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Detached Water Distribution Manifold
The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in. I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!
Racks rusted ,mounting bracket broken, seal leaked
replaced racks easy, pulled dishwasher out to replace seal and used pro-apoxy to secure bracked to washer, as both brackets were lose and would not clip in location.
Hey I hope this helps someone. . I was quite frustrated with out little dishwasher. It almost seemed that the dishes would come out dirtier than when they went in. Turns out we have hard water and it did a number on the parts of the dishwasher. Luckily, the parts were cheap enough that I thought I would give em a try. Between that and something called "dishwasher magic" I had success! One thing I wished I did differently was that I should have purchased two (2) wash arm retainer clips. . . I re-used an old one but it would have been nice to have all new parts inside. Needless to say, our dishes now are super clean. I have 6 young kids so our dishwasher gets a real workout. I may have to purchase a water softener down the road but for now we'll roll the dice. Hope this helps!
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Chris
July 31, 2017
My manifold distribution assembly brackets came off where they mount on the tub. They don,t want to push back on to the two plastic hubs that hold them to the tub. Is there some special way to get the square metal parts on to the plastic receivers?
For model number MDBH955AWW
Hello Chris,
Thank you for your question! The manifold should just snap back into the brackets,if the brackets are not holding onto the manifold firmly the tabs may be wore out and the bracket might need to be replaced.
Good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Stephanie
September 30, 2019
How do i reinstall the manifold mounting brackets to the tub wall part#ps11747693
For model number MDBTT70AWS
Hello Stephanie, thank you for your question. The brackets WP99002643 press and lock onto the squares cut out in the tub assembly. I hope this helps!
Was this helpful?
Thank you for voting!
Jim
October 29, 2019
The tabs that hold the bracket for the arm are missing one on each position. Are there replacement tabs for the tub?
For model number MDB6601AWW
Hello Jim, Thank you for the question. The tabs are only sold as part of the Top Wash Arm and Retainer PartSelect Number PS11743060. Hope this helps!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11747693
Manufacturer Part Number: WP99002643