Spark Igniter
Fits your CVGX2423B!
$67.13
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your CVGX2423B!
PartSelect Number
PS11744544
Manufacturer Part Number
WP7432P109-60
Manufactured by
Whirlpool
Product Description
Spark Igniter Specifications
This part creates the spark that lights the gas and starts the burners.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Gas igniter glows | but will not light
This part works with the following products:
Cooktop, Range.
This part works with the following products:
Jenn-Air.
Part# WP7432P109-60 replaces these:
AP6011348, 71002724, 7432P109-60
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 3 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
would not stop igniting even after fire was on
unplugged unit from wall, disconnected gas line, and untaped the vent. disconnect the control knobs and unplugged and removed the control unit from the main unit. pulled the main unit out from the countertop and set it on a table. disconnect the burners and spark iginiters from the main unit. undo screws holding chrome brackets and stove base, to access iginiter. disconnect wiring from igniter and the one screw, replace iginiter. reverse everything to re-install
Other Parts Used:
-
Bill from Pearland, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Wrench set
19 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we had to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Other Parts Used:
-
Marlene from Dana Point, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
12 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed
took the nuts off &replaced the new ignited
Other Parts Used:
-
Robert from Pleasanton, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11744544
Manufacturer Part Number: WP7432P109-60
Manufacturer Part Number: WP7432P109-60
Brand
Model Number
Description