Oven Door Spring
Fits your 99548!
$40.80
Special Order
Fits your 99548!
PartSelect Number
PS11740694
Manufacturer Part Number
WP308126
Manufactured by
Whirlpool
Troubleshooting
This part works with the following products:
Range, Wall Oven, Microwave Oven Combo.
This part works with the following products:
Whirlpool, KitchenAid, Kenmore, Roper.
Part# WP308126 replaces these:
308126
Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 2 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
both upper oven door springs broke. Door would not stay closed except with "self-cleaning latch in place"
I HAVE NOT FOUND ANY GOOD DESCRIPTION OF HOW TO REPLACE DOOR SPRINGS ON A BUILT-IN DOUBEL OVEN ANYWHERE ON THE INTERNET. I HOPE THIS WILL BE OF HELP TO SOMEONE.
I correctly assumed it was the springs that broke. With the springs in hand I shut off the power at the breaker box. I removed both oven doors. The upper oven door required the removal of one screw for each hinge. Then with the door slightly open, wiggle and pull upward and the door detached from the hinge. The lower oven door is removed by just wiggling and lifting with the door slightly open. I then removed 8 screws that fasten the oven to the cabinet. I removed 3 screws that hold the bottom vent cover in place and wiggling and pulling downward the vent cover detached. The bottom of the oven was 11 inches above the floor. I placed two sturdy objects about 10 inches tall in front of the oven and lifting, wiggling, and pulling the oven moved forward. I pulled it out about 2/3 of its depth.
The sheetmetal sides of the oven are indented and the spring attachments are easily accessible. ONE TROUBLE SPOT. The back end of the spring attaches to the cabinet but there is a small metal piece called an "anchor" that attaches to the front of the spring and then to the hinge. When the spring breaks the anchor goes flying. I was able to retrieve one of the anchors but the other one fell down between the insulation and the side of the cabinet and I was not able to retrieve it with out pulling the side loose. I was afraid I would run into other issues if I did that. So my oven is sitting in the kitchen while I wait 3 days for a replacement anchor.
The anchor is about $7 and the 2-3 day shipping is $10 so you might do well to just order one along with the spring.
I ordered a pair of lower door springs at the same time. About $10 each. Worth it to me not to repeat this process in the near future.
Once the oven is pulled out, the springs are very easy to install. I did all three I could do in about 10 minutes max.
MY BIGGEST PROBLEM was deciding how to get at the springs. All diagrams in the installation manual showed solid metal sides on the oven. They did not show that the springs we easily accessible outside the oven case. I was pleasantly surprised to see the indentations as I started to slide the oven out of the cabinet!
With the springs installed, I will just push the oven back into the cabinet, install the 8 screws, replace the lower vent cover and install the doors. Turn on the breaker and receive the applause of my wife for my marvelous ability!
I correctly assumed it was the springs that broke. With the springs in hand I shut off the power at the breaker box. I removed both oven doors. The upper oven door required the removal of one screw for each hinge. Then with the door slightly open, wiggle and pull upward and the door detached from the hinge. The lower oven door is removed by just wiggling and lifting with the door slightly open. I then removed 8 screws that fasten the oven to the cabinet. I removed 3 screws that hold the bottom vent cover in place and wiggling and pulling downward the vent cover detached. The bottom of the oven was 11 inches above the floor. I placed two sturdy objects about 10 inches tall in front of the oven and lifting, wiggling, and pulling the oven moved forward. I pulled it out about 2/3 of its depth.
The sheetmetal sides of the oven are indented and the spring attachments are easily accessible. ONE TROUBLE SPOT. The back end of the spring attaches to the cabinet but there is a small metal piece called an "anchor" that attaches to the front of the spring and then to the hinge. When the spring breaks the anchor goes flying. I was able to retrieve one of the anchors but the other one fell down between the insulation and the side of the cabinet and I was not able to retrieve it with out pulling the side loose. I was afraid I would run into other issues if I did that. So my oven is sitting in the kitchen while I wait 3 days for a replacement anchor.
The anchor is about $7 and the 2-3 day shipping is $10 so you might do well to just order one along with the spring.
I ordered a pair of lower door springs at the same time. About $10 each. Worth it to me not to repeat this process in the near future.
Once the oven is pulled out, the springs are very easy to install. I did all three I could do in about 10 minutes max.
MY BIGGEST PROBLEM was deciding how to get at the springs. All diagrams in the installation manual showed solid metal sides on the oven. They did not show that the springs we easily accessible outside the oven case. I was pleasantly surprised to see the indentations as I started to slide the oven out of the cabinet!
With the springs installed, I will just push the oven back into the cabinet, install the 8 screws, replace the lower vent cover and install the doors. Turn on the breaker and receive the applause of my wife for my marvelous ability!
Other Parts Used:
-
David from GALT, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
9 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bad element and burner clips were broken
Pulled out the stove and unplugged. Removed the back of the oven and removed the element connections. Removed the two screws holding the element in place and installed the new one.
Removed the remaining parts of the old clips and installed the new ones. Very easy
Removed the remaining parts of the old clips and installed the new ones. Very easy
Other Parts Used:
-
Robert from Cincinnati, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
4 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11740694
Manufacturer Part Number: WP308126
Manufacturer Part Number: WP308126
Brand
Model Number
Description