Part Location Diagram of WP22003059 Whirlpool Remote Style Pump with Motor - 120V 80W
See part 005 in the diagram
Replacing your Maytag Washer Remote Style Pump with Motor - 120V 80W
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Remote Style Pump with Motor - 120V 80W

★★★★★
★★★★★
3 Reviews
$184.76
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11739411
Manufacturer Part Number WP22003059
Manufactured by Whirlpool
Product Description

Remote Style Pump with Motor - 120V 80W Specifications

This remote style pump and motor assembly with check valve is used for some washing machines. The motor attached to this pump carries 120 volts and 60 hertz.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Maytag Washer Remote Style Pump with Motor - 120V 80W

Replacing your Maytag Washer Remote Style Pump with Motor - 120V 80W
Troubleshooting
This part fixes the following symptoms:
Will not drain | Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag.
Part# WP22003059 replaces these:
AP6006338, 22001982, 22002550, 22002794, 22002939, 22003059
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
3.3
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.0 / 5.0, 20 reviews. What's this?
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Washer not draining
Unplug washer, turn off water, disconnect supply hoses.
Drain washer by removing the one screw holding the hose on the bottom rear of the washer, drop the hose to the floor and let it drain (you may want to take washer outside)
Remove four screws holding rear panel
Locate the pump and disconnect the two wires. Wires can be attached to either terminal when reinstalling, orientation is not important.
Using 5/16 driver, loosen the hose clamps on the inlet and outlet pump hoses then remove hoses from pump.
Twist the pump counter clockwise then pull straight up to remove.
Other Parts Used:
  • Timothy from Bremerton, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
65 of 68 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the water drain pump started to make grinding noises and poor draining
the repairs couldn't be easier, the pump came right out. just loosen the two water drain hoses and out it came. the intallation was just as easy...
Other Parts Used:
Light Bulb - 10W
  • carlos from rio rancho, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
21 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
change stuck in drain pump, damaged the motor
just replaces the pump , the replacement pump was a little different than OE , mounting bracket different but was able to remove housing and bracket from broke pump and put on new pump , all works fine
Other Parts Used:
  • gordon from indianapolis, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It went like butter
it's best to pull off the back of washer then it is too go through the front thats my only hint
Other Parts Used:
  • Charnell from Tacoma, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not spin the water out of machine.
The pump motor was making quite a chattering noise about 2 months before it totally quit, Ordered part it was shipped very fast.(before the next wash day). Took the back off remove 2 hoses and 2 wires installed new motor. Very easy job and it is working very quite and great.
Other Parts Used:
  • Benny from Shelbiana, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The pump would not empty the washer.
I had taken the back off the washer already. The pump was connected to an incoming fitting and the out going fitting with hose clamps. Removed the hose and hose clamps from the old pump, connected the hose and hose clamps to the new pump, reconnected the wiring and that was about it. The pump was mounted to the bottom panel of the washer by simply plastic plugs requiring no tools. It was very easy.
Other Parts Used:
  • Wilson from Logansport, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bad pump
I took off the rear panel and removed the hose clamps and electrical terminals, slid pump out of slot in bottom pan of washing machine. It only took minutes, this was part of a major overhaul. I replaced this as a precautionary measure. Great prices and quick service,
Other Parts Used:
Short Dispenser Door Retaining Pin Hinge Pin Dispenser Lid Door Boot Drain Hose Dispenser Bezel Drive Belt and Motor Isolator Kit
  • Brandon from Berea, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
6 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not pump out water
I have a new Matag repairman, my husband. He took the front panel off by removing the screws. Then removed the balance on the drum and found the pump. Put the new one on and put everything back and my washer runs better than it has in a long time. Saved us a service call and hourly rate for a service man that couldn't come for 4 days.
Other Parts Used:
  • Linda from Sunbury, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Machine had been making a howling noise during rinse cycles for several weeks and then suddenly stopped draining.
On-line trouble shooting sites indicated that drain pump was likely culprit. Disconnected pump from hoses and removed and replaced pump. Tub to pump hose had considerable scale in it, so replaced that too. Repair was made easier by removing both the front and back panels of the washer to get best access to hose clamps and pump.
Other Parts Used:
Tub to Pump Hose
  • Todd from Anchorage, AK
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not pump out water
I removed the pump and found several coins had damaged the prop blade. I ordered a new one and installed it easily. The intake on the new pump was slightly smaller than the original so the original quick clamp produced a leak. A simple manual hose clamp corrected that problem.
Other Parts Used:
  • Joella from Parkville, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11739411
Manufacturer Part Number: WP22003059
Brand
Model Number
Description
Maytag
MAH14PDAAL
Washer - Commercial
Maytag
MAH14PDAAQ
Washer
Maytag
MAH14PDAAW
Washer - Commercial
Maytag
MAH14PDABL
Washer - Commercial
Maytag
MAH14PDABW
Washer - Commercial
Maytag
MAH14PDCBQ
Washer
Maytag
MAH14PDCBW
Washer
Maytag
MAH14PDDWW
Washer
Maytag
MAH14PNAWW
Washer
Maytag
MAH14PRAWW
Washer
Maytag
MAH14PSAAW
Washer - Commercial
Maytag
MAH20PDAWQ
Washer
Maytag
MAH20PDAWW
Washer - Commercial
Maytag
MAH20PDCXQ
Washer
Maytag
MAH20PDCXW
Washer
Maytag
MAH20PNAWW
Washer
Maytag
MAH20PRAWW
Washer
Maytag
MAH20PRDWW
Washer
Maytag
MAH20PSAWW
Washer
Maytag
MAH3000AKW
Washer - Residential
Maytag
MAH3000AWA
Washer - Residential
Maytag
MAH3000AWQ
Washer - Residential
Maytag
MAH3000AWW
Washer - Residential
Maytag
MAH4000AWQ
Washer - Residential
Maytag
MAH4000AWW
Washer - Residential
Maytag
MAH5500AWW
Washer - Residential
Maytag
MHW2000AWW
Washer Dryer Combo
Maytag
MLE19PDAYW
Washer Dryer Combo
Maytag
MLE19PDAZW
Washer Dryer Combo
Maytag
MLE19PDCZW
Washer Dryer Combo - Electric
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service