Water Valve - 4 Coil
$249.59
Special Order
PartSelect Number
PS11739389
Manufacturer Part Number
WP22002795
Manufactured by
Whirlpool
Product Description
Water Valve - 4 Coil Specifications
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Maytag.
Part# WP22002795 replaces these:
AP6006316, 22002795
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 2 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water Leaking Into Drum When Machine Is Off
Removed the front door screws & front panel screws, removed screws in the "l" brackets holding the top down, tilted the top up & back, removed 3 hoses & 3 wire connectors from the old water valve. Removed 1 screw holding valve & replaced with new valve. Re-connected 3 wires & 3 hoses, replaced top & front door. While the machine was out from the wall, removed the back loovered cover, removed the old belt & removed 1 bolt holding motor. Removed th e motor, removed & replaced the 2 plastic insolators with the new ones supplyed with the belt on the motor spindels, re-installed the motor & bolt, then the new belt that is self adjusting. Replaced back cover & put machine back online, easy deal for anyone with very basic mechanical knowledge
Other Parts Used:
-
SHANE from NUEVO, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Machine would spin, but not fill
Replaced the water valve, but that was not the problem. Problem was a burned out control circuit board caused when the machine's door lock (wax motor) failed. Failure of this $20 part destroyed the circuit board ($200). Beware! Check these other items before replacing the valve.
Other Parts Used:
-
KEITH from EVERGREEN, CO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
KARIN
January 13, 2022
I CAN'T GET ANY WATER
For model number MAH4000AWQ
Hi Karin,
Thank you for your question. If your washer is not filling with water, there are some parts that you will need to check to see which one is causing the issue. You will need to check the inlet hoses and screens, the water inlet valve, the door lock/spin enable switch, the water pressure switch, the temperature switch and the timer. We have included a link that you may reference on how to check these parts. We hope this helps! Good luck with the repair!
Was this helpful?
Thank you for voting!
Related Parts:
Additional Links:
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11739389
Manufacturer Part Number: WP22002795
Manufacturer Part Number: WP22002795
Brand
Model Number
Description