Average Repair Rating: 2.2 / 5.0, 3 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
had a rip in the bellow
easy remove the front panel it just pops off unscrew the top and lift up. you have a few pieces to remove then press the old rubber out and install new, i had a little trouble lining up the hardest part was putting the cable ban back on with the spring, i needed help from a friend. now the tub seal was not needed but with it apart I went ahead and changed it the clips were hard to snap on,:you need strong fingers to do that! reassemble as you took it apart. washer works fine no leaks, and alot cheaper than a new washer. thanks to parts select for the right parts MICK KEATING
leaking water at the seal between the drum and door assembly
I took the door off, front panel, soap dispenser(to lift the top out of the way)and took off the cross braces on the front of the machine. I pealed the door bellows off and took the drain hose apart; there was much gunk and debris to clean out...maybe something here was clogged? Removed all the snap clips and took the front of the tub off;the tub seal seemed good, but lots of grime/gunk build up.I cleaned all surfaces, put the new tub seal on,and put it all back togther. The hardest part was working the snap clips back on; I worked a few on both sides, top and bottom, and then filled in the rest. The machine has been working fine for a month now, no leaks:)
Other Parts Used:
max from antioch, IL
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
6 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace front and rear bearings and bellows
Of course I looked at you tube to get the instructions on how best to do the job. It was very helpful. Getting the front bearing out was the major issue. It was so corroded that I could not get it out with a hammer and punch. I had to build a bearing puller which I copied from the you tube video out of a 3" schedule 40 pipe. After that the repair went very smoothly. Putting on the bellows cable and spring assembly took two of us. Also putting the clips that held the inside drum on took two of us. One of us used channel loks to squeeze the two drums together while the other installed the clip. I had trouble identifying the tube seal part number. I phoned for help and the customer service person was very helpful and ordered me the correct part. Thank you
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeanne
January 15, 2019
I am looking to replace the rubber seal which has gotten moldy in my washer. It is located around the door front when you open the washer. Which exact part number do I need to order?
For model number MAH5500BWW
Hello Jeanne, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS2003890. I looked up the part and it is listed as No Longer Available/Discontinued. There is no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. Hope this helps!
I am looking for the gray door seal that has become too dirty and moldy. Can you help me find the part? Is it easy to install
For model number MAH55FLBWW
Hello Bobbie, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS2003890. I looked up the part and it is listed as No Longer Available/Discontinued. There is no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11739329
Manufacturer Part Number: WP22002077