![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Cook Top Base
$323.18
Special Order
PartSelect Number
PS11738714
Manufacturer Part Number
WP2001F175-09
Manufactured by
Whirlpool
Troubleshooting
This part works with the following products:
Cooktop, Range.
This part works with the following products:
Jenn-Air.
Part# WP2001F175-09 replaces these:
AP6005659, 2001F175-09, 74005897
Customer Repair Stories
Average Repair Rating: 2.8 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Replaced old Jenn Air cook top base
Prepare a flat area with newspaper, a screwdriver, and a small bowl for the screws, and a small wire brush (if you want to clean as you go). I also recommend taking photos as you proceed, for reference.
ALSO, take close note of the orientation of the cook top base, one end has a lip that's allows for burner assembly removal.
Remove entire two burner assembly, place upside down on newspaper, remove seven Phillips screws, remove assembly bottom.
Remove small screws from gas tubes, pay close attention as you remove the gas tube from the bottom of the burner, to the orientation of the two washers (the washers have an edge).
Remove the burner tubes and washers.
Carefully remove the igniter connectors from igniter.
Remove the end of the assembly.
Grasp the burners, and turn to rotate the burner to a position where the "bumps" on the burner match up with the gaps in the burner cook base. Remove the burners.
The old burner base can be set to the side. At this time i cleaned the burners throughly with a small toothbrush size wire brush.
Assemble the burners to the new top base by aligning the bumps to the opening in the cook top base, turn slightly to keep burner in place. Insert the gas tubes, with the washers (be careful about the washer lip orientation) with the smaller screws, do not overtighten!
Attach the igniter connector to the igniters.
Align the burner/gas tubes with the assembly end. Carefully set the base into place, adjust the tubes as necessary to get the screws aligned with the holes. Install the screws, tighten hand tight.
Install entire assembly into cook top, check igniter and burner operation.
Glass cleaner is great for cleaning the new porcelain surface.
ALSO, take close note of the orientation of the cook top base, one end has a lip that's allows for burner assembly removal.
Remove entire two burner assembly, place upside down on newspaper, remove seven Phillips screws, remove assembly bottom.
Remove small screws from gas tubes, pay close attention as you remove the gas tube from the bottom of the burner, to the orientation of the two washers (the washers have an edge).
Remove the burner tubes and washers.
Carefully remove the igniter connectors from igniter.
Remove the end of the assembly.
Grasp the burners, and turn to rotate the burner to a position where the "bumps" on the burner match up with the gaps in the burner cook base. Remove the burners.
The old burner base can be set to the side. At this time i cleaned the burners throughly with a small toothbrush size wire brush.
Assemble the burners to the new top base by aligning the bumps to the opening in the cook top base, turn slightly to keep burner in place. Insert the gas tubes, with the washers (be careful about the washer lip orientation) with the smaller screws, do not overtighten!
Attach the igniter connector to the igniters.
Align the burner/gas tubes with the assembly end. Carefully set the base into place, adjust the tubes as necessary to get the screws aligned with the holes. Install the screws, tighten hand tight.
Install entire assembly into cook top, check igniter and burner operation.
Glass cleaner is great for cleaning the new porcelain surface.
Other Parts Used:
-
David from MECHANICSVLLE, MD
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Yolanda
April 27, 2018
Can I replace the cook top base myself or do I need to call an installer?
For model number JGD8130ADS
Hi Yolanda, Thank you for the question. Most customers have been able to do the repair on their own, but it will depend on your experience. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Colleen
October 12, 2021
The flame is leaking out below the burner head. Is the cook top base the part to replace or the burner head?
For model number Jgd8348bdp
Hello Colleen, thank you for your question. We have researched the model you have provided, and we would suggest the burner head. We hope this helps!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11738714
Manufacturer Part Number: WP2001F175-09
Manufacturer Part Number: WP2001F175-09
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)