Models
>
PT956SM1SS
PT956SM1SS General Electric Wall Oven - Overview
Sections of the PT956SM1SS
[Viewing 7 of 7]Manuals & Care Guides for PT956SM1SS
Click to downloadInstall
Installation Instructions
(1.74MB)
Install
Installation Instructions
(2.10MB)
Manual
Owner's Manuals
(2.95MB)
Keep searches simple, eg. "belt" or "pump".
Meat Probe Thermistor
PartSelect #: PS1481046
Manufacturer #: WB20T10024
This probe is used to check the internal temperature of the meat to ensure proper temperature is reached. Also known as a Meat Probe.
$75.73
Special Order
Light Bulb - 40W
PartSelect #: PS217532
Manufacturer #: 40A15
This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible wi...
$5.85
Special Order
Oven Sensor
PartSelect #: PS236398
Manufacturer #: WB23T10015
This temperature sensor detects the temperature within the oven cavity.
$59.44
Special Order
Door Gasket
PartSelect #: PS1019820
Manufacturer #: WB04T10050
This oven door gasket prevents heat from escaping the oven cavity when in use.
$67.09
Special Order
Oven Bulb Lens Cover - Glass
PartSelect #: PS237483
Manufacturer #: WB25T10002
This part is the replacement oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover is rigid and protects the oven light bulb from being damaged. The main ...
$28.88
Special Order
Oven Light Housing
PartSelect #: PS230438
Manufacturer #: WB08T10002
Must buy bulb locally as per manufacturer.
$75.73
Special Order
Questions And Answers for PT956SM1SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the PT956SM1SS
[Viewing 5 of 5]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven was not coming up to temperature
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out.
Parts Used:
-
Sean from Highlands Ranch, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
55 of 70 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Lamp Holder Burned
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.
Parts Used:
-
Jack from Okmulgee, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
23 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Actual temperature did not match set temp
Removed the oven door for easy acces to oven. Unscrewed (philips screwdriver) the screw holding temp sensor in place. Gently pulled the wiring until quick connector was located. Pushed down on locking level on quick connect while holding other end of wiring (so wiring would not fall back behind oven). Connected the new sensor and screwed back in place. Reinstalled oven door. Tested temperature settings by turning on oven and comparing with a separate oven thermometer.
Parts Used:
-
Brian from Fairfield, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
21 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!