Models
>
PR230K1
PR230K1 Hotpoint Cooktop - Overview
Sections of the PR230K1
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
![Surface Element - 6 Inch - 240V – Part Number: WB30M1 Surface Element - 6 Inch - 240V – Part Number: WB30M1](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/243867-1-S-GE-WB30M1-Surface-Element-6-Inch-240V.jpg)
Surface Element - 6 Inch - 240V
PartSelect #: PS243867
Manufacturer #: WB30M1
This Y-frame six inch surface burner element has five turns and a metallic center medallion.
$72.98
Special Order
![Surface Burner Terminal Block Kit – Part Number: WB17X210 Surface Burner Terminal Block Kit – Part Number: WB17X210](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/232606-1-S-GE-WB17X210-Surface-Burner-Terminal-Block-Kit.jpg)
Surface Burner Terminal Block Kit
PartSelect #: PS232606
Manufacturer #: WB17X210
This kit comes with the terminal block, mounting clip and wires.
$91.36
Special Order
![Infinite Switch Burner Knob – Part Number: WB3X800 Infinite Switch Burner Knob – Part Number: WB3X800](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/249164-1-S-GE-WB3X800-Infinite-Switch-Burner-Knob.jpg)
Infinite Switch Burner Knob
PartSelect #: PS249164
Manufacturer #: WB3X800
Sold Individually. This knob accepts a double-flat shaft.
No Longer Available
Questions And Answers for PR230K1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the PR230K1
[Viewing 2 of 2]Element will not heat
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/243868_1_S.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/243867_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/232606_1_S.jpg)
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/243868_1_S.jpg)
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Parts Used:
-
Shaohui from East Lansing, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
48 of 52 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of Coils
Removed by slightly wiggling out of the coupling. No tools needed, seriously, (and I'm a contractor). Basically, pull out and snap back in.
Parts Used:
-
Joseph from South Plainfield, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
35 of 42 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Surface burner coil did not work.
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Parts Used:
-
Gregory from Mont Belvieu, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
23 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!