Models
>
MMV5207BAB
MMV5207BAB Maytag Microwave - Overview
Models starting with MMV5207BAB
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Door Handle - Stainless
PartSelect #: PS11749865
Manufacturer #: WPW10187840
Handle only.
$128.19
In Stock
Door Handle - Black
PartSelect #: PS2330325
Manufacturer #: W10189508
Screws are NOT included.
No Longer Available
High Voltage Capacitor
PartSelect #: PS1486840
Manufacturer #: 8206562
This is an electronic device that holds a charge of electricity.
$119.27
In Stock
Microwave Magnetron
PartSelect #: PS11748664
Manufacturer #: WPW10126786
This part is used to generate microwave energy/heat.
$290.93
Special Order
Common Symptoms of models starting with MMV5207BAB
[Viewing 4 of 4]No heat
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Exhaust fan not working
Fixed by
these parts
these parts
Show All
Door not closing properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken handle
Remove the door by lifting up the hinge side so that the two hinge pins disengage from the steel hinge brackets.This can be a bit fiddly so just keep wiggling the door until one of them pops off.
Remove the plastic cover trim piece that surrrounds the window, exposing the phillips head screws that secure the door to the handle.
Remove the screws to un-install the old handle, they are deep set so if they fall out of the door you will need needle nose pliers to pout them back into the door.
Set teh new handle in place and tighten the screws down snuggly.
Retrace your steps... snap the plastic trim back in place and reset teh door on it's hinges (once again this can be a bit fiddly so take your time.
Eat a Burrito!
Remove the plastic cover trim piece that surrrounds the window, exposing the phillips head screws that secure the door to the handle.
Remove the screws to un-install the old handle, they are deep set so if they fall out of the door you will need needle nose pliers to pout them back into the door.
Set teh new handle in place and tighten the screws down snuggly.
Retrace your steps... snap the plastic trim back in place and reset teh door on it's hinges (once again this can be a bit fiddly so take your time.
Eat a Burrito!
Parts Used:
-
Raymond from Bishop, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
43 of 52 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grease filters were missing from the over-the-stove microwave
Why a tenant would remove and discard the grease filters without replacing them is beyond me! But, I removed the filters from the package and slid them into place. Two minutes tops. I would like to add that I ordered these on Thursday afternoon, and I had them on Saturday; awesome customer service!
Parts Used:
-
Lori from Salt Lake City, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
64 of 127 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not the original type bulb
The repair was very easy, however the bulb was not the same as the original one. The original bulb had a bright setting and a low setting, but the replacement bulb was only the low setting bulb. There was no bright and dim operation. The switch on the microwave had the duel settings.
Parts Used:
-
John from Orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
29 of 35 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!