Models
>
LMC1575SB
LMC1575SB ((CB1ELNA)) LG Range - Overview
Sections of the LMC1575SB
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Turntable Motor Coupler
PartSelect #: PS3522918
Manufacturer #: 4370W1A006B
The turntable motor coupler connects the turntable motor to the tray. If the turntable on your microwave will not rotate, you may have a faulty motor coupler. The coupler commonly has a D shaped openi...
$25.93
In Stock
Questions And Answers for LMC1575SB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
October 21, 2023
LG Microwave stopped heating food. Otherwise it all functions normally, except after selecting the cook time and it counts down, we open the door and the food is not heated. What do you think is most likely to be the problem?
For model number LMC1575SB
Hi Robert, thank you for contacting us. We believe your microwave is having this problem due to a faulty magnetron, part number PS12383382, which may need to be replaced. We hope this helps, good luck with the repair!
Was this helpful?
Thank you for voting!
Related Parts:
MAGNETRON
$169.61
In Stock
- < Prev
- 1
- Next >
Common Symptoms of the LMC1575SB
[Viewing 3 of 3]Won’t turn on
Fixed by
these parts
these parts
Show All
Tray won’t turn
Fixed by
these parts
these parts
Show All
No heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sparks from an old wave guide that needed to be replaced
Put microwave on its side as my hands weren’t ready enough to hold it up while trying to push it in.
Put board on the door to hold it open.
Gently pushed the wave guide back as far as it would go. Then, I carefully pushed the front tabs in place. No bending. I had practiced on the old one first. Broke the 2 old tabs by pushing back to hard so you need to be careful.
Put board on the door to hold it open.
Gently pushed the wave guide back as far as it would go. Then, I carefully pushed the front tabs in place. No bending. I had practiced on the old one first. Broke the 2 old tabs by pushing back to hard so you need to be careful.
Parts Used:
-
Ellen from REDDING, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The new part was too thick for the worn out plastic ring which is obsolete.
Needed to raise the part to match the ring. I used peanut butter to hold plastic shim while replacing to hold it in place. Built in Oct. 2009.
Parts Used:
-
James from PURCELLVILLE, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Shaft socket was worn out
-
Cesar from Miami, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!