Models
>
LDG3016ST
LDG3016ST ((00)) LG Range - Overview
Sections of the LDG3016ST
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Burner Knob - Stainless Steel
PartSelect #: PS7321756
Manufacturer #: AEZ73453509
Sold individually. This knob accepts a D-shaped shaft.
$145.44
In Stock
TRANSFORMER ASSEMBLY,POWER
PartSelect #: PS16732632
Manufacturer #: EBJ64465501
The spark module controls the spark for lighting the cooktop surface burners.
$71.70
In Stock
CAP,BURNER
PartSelect #: PS3627296
Manufacturer #: MBL61908604
The burner cap attaches to the top of the burner head and acts like a cover for the burner head. This part helps to protect the burner from spills and helps to even the flame while cooking. The cap is...
$82.09
Special Order
LP Conversion Kit
PartSelect #: PS3639908
Manufacturer #: AGM73069204
Conversion kit from Natural gas to LP.
$136.93
In Stock
Questions And Answers for LDG3016ST
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the LDG3016ST
[Viewing 6 of 6]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven wouldn't ignite
Took off the oven door then took out the racks and two screws in the oven bottom and removed it . Then removed the heat deflector. Then un plugged the old igniter and removed the burner to make it easier to remove the old igniter. Then installed the new igniter and reversed the process
Parts Used:
-
Martin from KEWASKUM, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not light
As soon as my husband put it in the oven, the very thin prongs broke. There was no guard on either side of the prongs for protection like the one that had been in there. Very costly to us of $185 with no fix. Very disappointed in that ignitor. It would have been an easy fix. Had replaced one previously but it only lasted 6 months. Now we have a new stove
Parts Used:
-
Sheila from HOPKINTON, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
6 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F3 Error Code
F3 Error code. Most documentation suggested checking oven sensors. They were good (Checked 1050 & 1080 Ohms). Next most common problem was bad connection somewhere. This was not problem. Documentation then suggested it would be main system board. This did not fix problem. If I shut power off disconnected key pad error F3 did not come back (although the PF power failure stayed on as no key pad). If I shut power off and plugged in key pad PF (power failure) came on and in a short time F3 appeared. I changed key pad and problem is gone.
Parts Used:
-
George from CORTLAND, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!