This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
This is a basket for washing flatware or silverware in your dishwasher. This is a manufacturer-approved replacement silverware basket for your dishwasher. To replace this part simply remove the existi...
This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Als...
This is a door seal, but you may also know it as a door gasket and it is a part for your dishwasher. It provides a leak proof seal between the tub and the door of your appliance. You will need to repl...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Amy
June 16, 2021
How do i reset control panel?
For model number KUDL02FRSS1
Hello Amy, Thank you for the question. To reset the appliance/panel, you just need to turn the power off to the appliance at the breaker or unplug it from the outlet for at least 5 mins. This will reboot the panel. We hope this helps!
Was this helpful?
Thank you for voting!
Denise
July 12, 2021
My kitchen aid dishwasher model number KUDL02FRSS1 stopped working -no power at all, display not lighting. The circuit board looks like its fried, a tech ordered a new board, still not working, no power. The connector cable to the board looks burnt. I have looked for the part and have not been able to find anything that looks like it. Can you assist?
For model number KUDL02FRSS1
Hello Denise, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11728129. We hope this helps!
Dishwasher will not start a cycle. The "Clean" indicator flashes 7 times. Have unplugged the unit to reset it with no change at all.
For model number KUDL02FRSS1
Hello Michael, thank you for your inquiry. We have found that the clean light blinking seven times can be due to bad heater element, thermostat, or a control board. Most of the time, it's due to a low water temperature. We would recommend checking the heating element, part number PS11748194, to fix the issue. Glad to be of assistance!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
