Models
>
JS750SF1SS
JS750SF1SS General Electric Wall Oven - Overview
Sections of the JS750SF1SS
[Viewing 7 of 7]Manuals & Care Guides for JS750SF1SS
Click to downloadInstall
Installation Instructions
(1.84MB)
Install
Installation Instructions
(0.5MB)
Install
Installation Instructions
(1.38MB)
Manual
Owner's Manuals
(11.5MB)
Keep searches simple, eg. "belt" or "pump".
REAR SUPPORT
PartSelect #: PS12709839
Manufacturer #: WB02X33180
This rear drawer support comes with the installation screw. This part has been redesigned. The new support inserts towards the rear of the drawer as opposed to the side.
No Longer Available
Foot - Leveller
PartSelect #: PS223802
Manufacturer #: WB02X10521
Sold individually.
$29.77
Special Order
RANGE HALOGEN BULB KIT
PartSelect #: PS12342510
Manufacturer #: WB49X29679
This light bulb is used in the interior oven. NOTE: This bulb has looped pins, not the straight pins.
No Longer Available
Oven Sensor
PartSelect #: PS236398
Manufacturer #: WB23T10015
This temperature sensor detects the temperature within the oven cavity.
$59.44
Special Order
ELEMENT HALIANT 12 TRIPLE
PartSelect #: PS8754838
Manufacturer #: WB30T10155
This surface element is for ranges.
Surface element supplies the heat to a cooking area on top of the range.
Unplug the range or shut off the house circuit breaker for the range before installin...
$313.16
Special Order
Infinite Switch Control
PartSelect #: PS236751
Manufacturer #: WB24T10026
This surface element control switch is for ranges.
Surface element control switch turns the surface element on and off and controls how much heat the element produces.
Unplug the range or shut o...
$61.24
Special Order
Questions And Answers for JS750SF1SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
February 27, 2023
Only convection bake and warming zone work.
For model number JS750SF1SS
Hello John, thank you for contacting us. According to our research, the issue is most probably with the control board, part number PS11700842. You may need to replace the control board. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the JS750SF1SS
[Viewing 6 of 6]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven was not coming up to temperature
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out.
Parts Used:
-
Sean from Highlands Ranch, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
55 of 70 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
terminal block melted
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
Parts Used:
-
jonathan from willow springs, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
53 of 69 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic drawer support snapped off
The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.
Parts Used:
-
Jeff Troiano from Sayville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
30 of 32 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!