Models
>
GB135FL4
GB135FL4 Frigidaire Cooktop - Overview
Sections of the GB135FL4
[Viewing 2 of 2]Keep searches simple, eg. "belt" or "pump".
![Top Burner Mounting Screw with Washer – Part Number: 316069301 Top Burner Mounting Screw with Washer – Part Number: 316069301](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/437925-1-S-Frigidaire-316069301-Top-Burner-Mounting-Screw-with-Washer.jpg)
Top Burner Mounting Screw with Washer
PartSelect #: PS437925
Manufacturer #: 316069301
This is now a new zinc and black-coated screw that will resist rust and
seizing.
$2.29
In Stock
![Spark Module – Part Number: 316135702 Spark Module – Part Number: 316135702](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/2350722-1-S-Frigidaire-316135702-Spark-Module.jpg)
Spark Module
PartSelect #: PS2350722
Manufacturer #: 316135702
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$129.84
In Stock
![Igniter Switch – Part Number: 316032002 Igniter Switch – Part Number: 316032002](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/437310-1-S-Frigidaire-316032002-Igniter-Switch.jpg)
Igniter Switch
PartSelect #: PS437310
Manufacturer #: 316032002
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.
$74.53
Special Order
Questions And Answers for GB135FL4
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the GB135FL4
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/2350722_1_S.jpg)
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/2350722_1_S.jpg)
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
gas ignitor continued to run after turned on or off
Removed all of the grates, control knobs and gas diffusers. Unscrew the drip pans, two on each pan, which attach the pans to the gas supply. Raised the drip pans from the top and unplugged the ignitors from all pans. Remove the top and the rubber deflector over the ignitor switch. The ignitor switch snaps off and on. One of the seals under the drip pan was broken and needed replaced. I would recommend ordering these also. Turned out this was a good time to give everything a goo cleaning then replace as removed.
Parts Used:
-
Duff from Buena Vista, CO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top burners were not lighting without a match
Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly
Parts Used:
-
Earl from ALLIANCE, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner ingnighter would not lite burner
Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.
Parts Used:
-
Wayne from Palestine, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
30 of 86 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!