Models
>
FAV6800AWW
FAV6800AWW Maytag Washer - Overview
Sections of the FAV6800AWW
[Viewing 9 of 9]Manuals & Care Guides for FAV6800AWW
Click to downloadKeep searches simple, eg. "belt" or "pump".
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
This hose clamp is sold individually.
$14.11
In Stock
Drain Pump - 120V 60Hz
PartSelect #: PS11740556
Manufacturer #: WP25001052
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$189.46
In Stock
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$27.37
In Stock
Leveling Leg and Pad
PartSelect #: PS2026623
Manufacturer #: 25001119
This part includes locknut.
No Longer Available
Inlet Hose Washer
PartSelect #: PS11757437
Manufacturer #: WPY013783
This high pressure inlet hose washer is black. It is an inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers.
$9.68
Special Order
Hinge Bushing
PartSelect #: PS11739381
Manufacturer #: WP22002753
Sold individually.
$9.67
Special Order
Plastic Hinge
PartSelect #: PS11739495
Manufacturer #: WP22004095
Sold individually.
$51.37
Special Order
Screw
PartSelect #: PS11742733
Manufacturer #: WP489128
This screw is sold individually.
$16.74
In Stock
Outer Tub Splash Guard
PartSelect #: PS2026645
Manufacturer #: 25001179
*May be different in appearance but will function as the original part.
No Longer Available
Questions And Answers for FAV6800AWW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Anthony
March 7, 2020
My drive belt broke and i need to know how to check if my clutch assembly is good.
For model number FAV6800AWW
Hello Anthony,
Thank you for your question. Most of the time, if the belt broke or burned, the clutch pulley would need to be checked for any physical defects, by inspecting it visually you will be able to tell if there are any issues. We hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the FAV6800AWW
[Viewing 3 of 3]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old Pump Stopped Draining The Machine- Impeller In Pump Wore Out
First- I unplugged and completely drained machine of water by putting hose at ground level near drain . Second- removed back plate to washer saving all hardware. Third- disconnected in and out hose to pump. Twisted pump gently as to pop it out of slots in bottom of machine. Fourth- disconnected wires to old pump hooked to new pump replaced pump, replaced hoses- tested machine then replaced back plate of machine. Done.
Parts Used:
-
Deborah from Westfield, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
79 of 87 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Belt Broke
Luckily, I found someone else with the same story, and read that you need the clutch assembly and the belt at the same time. One night when we started the washer, it made a metal seizing type squeal. There was smoke everywhere. After opening the washer, the belt burned through but the clutch had also seized which was the cause. Replaced both. Needle bearings were totally rusted. Must be leaking water somewhere. Just lift top, remove front cover (two screws inside the top). Prop up and secure washer. Loosen the motor bolt. Through the hole in bottom, fit socket to hex bolt on clutch. Our belt was already off as it broke in half. Remove clutch, slip new one on and make sure it goes all the way back on transmission. Place the one bolt back on. Two people are helpful here! Place new belt on grooves of motor pully (while person 2 holds the agitators still) and then work belt down and around clutch. Ours was a tight fit! Have a person pull back on motor as you tighten the one bolt you loosened. There is an in/lb rating on clutch bolt. Put washer back down and panel back together. Pretty easy repair to save tons on a new washer.
Ordered parts on a Friday at 3:05 pm, and they were delivered the next day! Excellent service!!! This saved our day!
Ordered parts on a Friday at 3:05 pm, and they were delivered the next day! Excellent service!!! This saved our day!
Parts Used:
-
Nicole from Ottsville, PA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
19 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Pump
Roll washer out of drain pan on section of 3" PVC pipe. Unplug washer & disconnect hoses. Remove rear access panel with nutdriver. Disconnect wiring harness from pump. Disconnect hoses from pump using screwdriver and pliers. Twist pump counter-clockwise to separate from bottom of washer housing. Transfer electronic component from old to new pump. Install new pump in reverse order as above.
Parts Used:
-
Drake from Crofton, MD
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
21 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!