Models
>
C2Y486P2M1S1
C2Y486P2M1S1 General Electric Range - Overview
Sections of the C2Y486P2M1S1
[Viewing 12 of 12]Keep searches simple, eg. "belt" or "pump".
![Temperature Sensor – Part Number: WB21X22134 Temperature Sensor – Part Number: WB21X22134](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/10059162-1-S-GE-WB21X22134-Temperature-Sensor.jpg)
Temperature Sensor
PartSelect #: PS10059162
Manufacturer #: WB21X22134
This temperature sensor detects the temperature within the oven cavity.
$48.82
Special Order
![Door Handle Fastener – Part Number: WR01X11007 Door Handle Fastener – Part Number: WR01X11007](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/6447735-1-S-GE-WR01X11007-Door-Handle-Fastener.jpg)
Door Handle Fastener
PartSelect #: PS6447735
Manufacturer #: WR01X11007
This is a door handle fastener to secure the handle to your refrigerator drawer. It is also known and a mounting bolt or screw. It is approximately 1 inch in total length, and is made of metal.
$16.68
Special Order
![Ignitor Mounting Screw – Part Number: WB1X1293 Ignitor Mounting Screw – Part Number: WB1X1293](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/234519-1-S-GE-WB1X1293-Ignitor-Mounting-Screw.jpg)
Ignitor Mounting Screw
PartSelect #: PS234519
Manufacturer #: WB1X1293
Sold Individually.
$11.80
Special Order
![Burner Cap – Part Number: WB13T10067 Burner Cap – Part Number: WB13T10067](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/1019797-1-S-GE-WB13T10067-Burner-Cap.jpg)
Burner Cap
PartSelect #: PS1019797
Manufacturer #: WB13T10067
Sold individually.
$80.88
Special Order
Questions And Answers for C2Y486P2M1S1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the C2Y486P2M1S1
[Viewing 7 of 7]Little to no heat when baking
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/10059162_1_S.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/234519_1_s.jpg)
Show All
Oven not heating evenly
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/10059162_1_S.jpg)
Show All
Oven is too hot
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/10059162_1_S.jpg)
Show All
Will Not Start
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/10059162_1_S.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/1022004_1_S.jpg)
Show All
Element will not heat
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/10059162_1_S.jpg)
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/10059162_1_S.jpg)
Show All
Door won’t open or close
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/6447735_1_S.jpg)
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would go in to a F2 Error
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
Parts Used:
-
Peter from stamford, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
144 of 212 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't preheat above 300 degrees
Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.
Parts Used:
-
Gerald from Cape Canaveral, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
49 of 80 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I kept getting An F2 error and the temperature did not seem accurate
1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on
note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on
note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.
Parts Used:
-
Chad from Bloomington, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set, Wrench (Adjustable), Wrench set
28 of 35 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!